Jump to content
SAU Community

Recommended Posts

AssumIng you have two cars one with 4wd and one rwd, if you could overcome grip issue would 4wd and rwd have same acceleration givrn engine hp and weight is same?

Also does anyone here drive 700+ rb25? Is it laggy on 2.5 engine?

 

i wonder why i didn't change my bottom end to 3 liter to get much better torque and smaller lag

 

 

Link to comment
https://www.sau.com.au/forums/topic/480449-acceleration-rwd/
Share on other sites

For instance i wonder how a 2 liter evo can get 0-60 on 3.4 sec with 2 liter engine

 

lag will be huge and need 3 sec to get to the rev band

 

i am interested as no matter what power, R34 with 2.5 engine struggles to get low 0-60

 

also what is correlation between engine size and fuel consumption. Me thinking engine of 2.5 should consume much smaller fuel than 4.4

 

my m5 consumes less With 560 than the r34

i can only think of new technology and extreme precision on mapping but still there is almost 2 liter difference and fuel usage is same

Edited by drifter17a

All things being equal 4wd will always have better grip than 2wd

Fuel consumption is a function of power, weight (total work done) and efficiency.

In my view especially for a road car an RB30  is going to be better than an RB25 or even 26 or 28.

I have seen torque amp which is 48v turbo proving around 4 psi so it seems to match torque at very low rpm to what you achieve at 3.5k rpm hence boosting street acceleration 

 

i am done spending more money on rb25 as it is laggy so think if I put a top mount turbo with bigger turbo it will make acceleration even slower as boost will kick in around 4k

If your RB25 is in good condition consider getting a turbo from Hypergear. Read through some of his last few pages to see the results he is getting from his cost effective turbos.

But if its in need of a rebuild consider an RB30. With better than 9:1 compression you will get better pickup even off boost.

5 hours ago, drifter17a said:

lag will be huge and need 3 sec to get to the rev band

When launching a car the revs will be high and the turbo will then be able to make boost pretty quick, but the most obvious thing is a car doing that kind of time would be using launch control and making boost with the clutch disengaged before launching= no lag at all. Rolling on throttle is a different story.

 

You should have put a supercharged v8 in the car.

8 minutes ago, Ben C34 said:

When launching a car the revs will be high and the turbo will then be able to make boost pretty quick, but the most obvious thing is a car doing that kind of time would be using launch control and making boost with the clutch disengaged before launching= no lag at all. Rolling on throttle is a different story.

 

You should have put a supercharged v8 in the car.

Actually I have been looking at getting an M35 Stagea and an LS engine is looking more attractive than VH41 or VK56.

LS1 might be cheaper but VK56 is a pretty nice engine :) The good folks at harrop do a suitable kit.

And you wont be happy with an M35 after having had a good C34 for a while, just look at all those posts over the years. They are not the same animals at all.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You have just offended every teenage boy in America
    • Structured text and other high level PLC programing languages are not allowable in Functional Safety. They are very difficult to audit. My PLC stuff is almost exclusively oriented towards Burner Management Systems which are a particularly pernicious form of Safety Instrumented System, when implemented in an SPLC. Even the part of the code written to work in the non-safety logic part of the PLC, like with a Siemens S7-1500 series, still needs to be treated as if it was safety code, with access restrictions, code fingreprints and the like. And Allen Bradley can go EABODs. They ae full of shit. They have this whole lie going on where they say if you use a ControlLogix controller and its IO, and then just duplicate the IOs (ie, run in series or parallel depending on type, to try to make it "fail safe") and "use these programming styles and place these restrictions on what you do" that you can achieve SIL2. What a load of crap. They just get away with it because no-one in the US seems to understand the first thing about Functional Safety and carries on as if all they have to do is buy only SIL2 rated equipment and hey presto, it's a SIL2 system. Idiots. /rant
    • If you're really considering leaving it, a great question to ask is, is the magnet going to stick to the sump? The answer to the above is the same answer towards if I'd have any level of comfort leaving it... Personally, based on the cost of a motor if the magnet were to cause damage, I'd be fishing it out either way. Use the methods in here. It fit in through the plug hole, it'll come out.   PS, get a small actuatable claw for a bore scope. OR if you know a vet, they have really cool controllable scopes with hooks on the end. Supposedly they're like playing a video game. Ask if they can acquire you one of their scopes... Engine oil after all is just a different type of lube right? Will only make it easier on the next dog or cat...
    • All other (Boolean) logic functions though, are just built on those blocks above. Which does give you a lot of functionality in logic. It is basing that on using thresholds with analogue signals like GTS alluded to.   Not having things like timers will make it less useful for some of the ramp up logic you'd want, and again, on Haltecs capacity specifically, I'm not across anymore what you can / can't do with different tables.   I'm assuming, with your logic you want to implement, not only do you want your timing safeties, you're wanting to be able to derive the duty cycle for your solenoid, to maintain I'm assuming 175PSi? Or are you using a standalone WMI controller to maintain the DC correct, and you just want the Haltech working out which fuelling maps you should be on?
    • It doesn't seem to follow revs. Oddly it seems to follow TPS a little bit from what I can see, but with some delay a bit. IE end of the graph, when he lets off throttle fully, pressure drops a lot, then slowly builds back up, but rpm is on a nice cruisey drop off. I do agree though, it seems very electrically.
×
×
  • Create New...