Jump to content
SAU Community

Recommended Posts

Car: 1988 A31

Engine: RB20DET

Power: 190rwkw 15psi

Performance Mods: hybrid RX7 turbo, 3inch exhaust, Hybrid front mount, Boostworx remap, blitz pod filter and HKS EBC.

Dynoed: Boostworx

When: Month ago

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Car: R32 4 door

Engine: Rb25det

Power: 215 rwkw @ 13 psi

Performance mods: FMIC, Apexi 3 inch exhaust, WoahBro pump, TSL Remap with Rb20det ecu, AVCR, Stock turbo.... upgrade coming soon.

Dynoed: Turbo Tune (most accurate in adelaide)

When: not long ago

  • 1 month later...

Car: 1989 cefiro

Engine: rb25/rb26 hybrid

Power: 580whp 434ft/lbs TQ @ 1.2bar C16 gas

Performance Mods:87.25mm wiseco forgies 9.8:1, egale H beam RB26 rods, acl bearings, N1 oilpump, R32GTR crank:with custom collar, block line bored, and extra oiling for 26 crank, head quench removed, three angle valave job, hks 272 dur 8.5 lift cammies, hks springs & retainers, Tomei adj cam gears, tomei 2mm head gasket, ARP head studs, GReddy TD06H-25G 16cm turbine, GReddy SS exhaust mani, GReddy GT 50mm wastegate, 555cc injects, rb26 power fc de-jetro, Splitfire coil packs, GReddy intake Mani with Q45 TB, nismo intank fuel pump, bosch inline fuel pump, nismo fpr, power enterprise timing belt...etc...

Dynoed:UNNATURAL INC. Portland, Oregon, USA

When: NOV 12 2008

Mode:awesome

dynosheet.jpg

Edited by cefirosliderRB2.7
  • 4 weeks later...

Car: s2 R33 4 door

Engine: RB25det

Power: 182rwkw

Performance Mods: fmic,3inch staight thru,splitfires,0.5bar,stage 2 shift kit,standard turbo dumppipe & front pipe i think?

Dynoed: west torrens dyno centre

When: 16/8/2007

Mode:shoot out mode 4

Car: R32 4 door

Engine: Rb25det

Power: 283 rwkw 20 psi

Performance mods: FMIC, AM Performance exhaust and Split Dump, Bosch Motorsport pump, TSL Remap with Rb20det ecu, Blitz EBC, 3071R with GCG rear housing

Dynoed: Turbo Tune (most accurate in adelaide)

When: last sat

now redone...

  • 4 weeks later...
Car: s2 R33 4 door

Engine: RB25det

Power: 182rwkw

Performance Mods: fmic,3inch staight thru,splitfires,0.5bar,stage 2 shift kit,standard turbo dumppipe & front pipe i think?

Dynoed: west torrens dyno centre

When: 16/8/2007

Mode:shoot out mode 4

hay man i have the same car but im guessing yours is auto mine is a factory manual series 2 which are pritty rare im told. its got full exhaust no cat, fmic {1000 hp rated} pod it put out atw 165kw before the full exhaust and cooler so i am keen to see wHAT IT HAS NOW. i hope around 255 or more hp dont no ill have to find out. it was also not on shootout mode i found out later. any way cheers. nm8u.

Edited by nm8u

Car: R34

Engine: RB25DE (non turbo)

Power: 128 kW N/A, 171 kW NOS

Performance Mods: 3" stainless steel catback, apexi power fc, splitfire colipacks, airnix trust pod filter, 55hp ZEX nitrous oxide kit, custom extractors

Dynoed: Southern Hi Tech Dyno (128kW) and the Extreme Horsepower Show - Profix Marion Dyno

When: December

Mode:a shoot out mode, not sure which one

Car: 1988 A31

Engine: RB20DET

Power: 190rwkw 15psi

Performance Mods: hybrid RX7 turbo, 3inch exhaust, Hybrid front mount, Boostworx remap, blitz pod filter and HKS EBC.

Dynoed: Boostworx

When: Month ago

Just had my car tuned at turbo Tune, making 214RWKW on 15psi with a T3G turbo replacing the worn Rx7 turbo, dyno sheet to come soon, or Simon-R32 can vouch for it, you were at Turbo Tune when my car was being tuned.

  • 2 weeks later...

Car: 89' A31 Cefiro

Engine: RB20DET

Power: 120.4 kW on stock boost. Made 142rwkw last March.

Performance Mods: 3" turbo back exhaust, FMIC, Aftermarket Fuel Pump, Pod Filter.

Dynoed: Some Aussie Mufflers place on Port Road. When: 20th Jan 08

Mode:Shit knows...

Pod was extremely dirty when It was done... looking at increasing the boost in a few weeks. :banana:

  • 2 weeks later...

Car: ca31

Engine: rb20det

Power: 142rwkw (peaks at 12psi then fades off to about 10psi with the stock ceffy actuator)

Performance Mods: R34 turbo, k&n pod, lightened flywheel, hd clutch, walbro 600hp pump, 3" turbo back

Dynoed: springy motors

When: couple months back

Mode: shootout

Does this sound about right for a 34 turbo upgrade?

I'll try find my dyno sheet later and post a flick up

Car: 89' r32 gtst sedan

Engine: RB20DET

Power: 206.9rwkw @14.5psi

Performance Mods: 3" turbo back exhaust, Blitz panel filter, FMIC, gtr injectors, garrett hiflow (33 comp machined out, AVO .73 exhaust) rb26 pfc modded to fit rb20, splitfire coilpacks

Dynoed: CREATD Motorsports

Mode: Not sure doesnt say

Needs: z32 afm, fuel pressure reg, EBC and as much boost as it can take :cheers:

post-23551-1202559411_thumb.jpg

  • 4 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Back in January, I noticed my car felt noticeably weak. I had the injectors cleaned, which seemed to solve the problem -- until now. Recently, the car suddenly lost power again while driving. Suspecting the injectors, I brought it to the mechanic. He recommended replacing them entirely, saying the current ones were getting unreliable and fiddly to work with. I could not find a direct replacement for my current injectors. The closest match I found were 440cc injectors. This led me to look into the possibility of upgrading -- and of course, that would mean remapping the ECU. From my research I found: The OEM Part numbers are 16600-72L20 and 16600-72L21 Both the RB20DE and RB20DET use the same 270cc injectors. There are much better options out there over the old OEM injectors. Nistune could be a viable tuning option. While the RB20DE isn’t explicitly listed on their site, the ECU is essentially the same as the GTS-T version - just with a different map. The ECU code on mine is listed as supported. One concern is finding a tuner who works with Nistune. Aftermarket ECU like Haltech and Link, but this would be the most expensive choice (and possibly overkill for a mostly stock RB20DE) I admit that I am very new to the tuning scene and would appreciate any insight or recommendations regarding this.   These are some SAU links where I got some of my information from for reference: https://www.sau.com.au/forums/topic/380324-rb20de-injectors/ https://www.sau.com.au/forums/topic/477396-factory-270cc-injectors/  
    • The inspectors are not forensic by any means but if you forge your documents and/or badgings on vehicle parts and are found out, the consequences are just far bigger than if you just run illegal parts. And their job quite literally is to cross reference what parts you got installed and what your papers say you got. Something as silly as your suspension being 1mm too low will fail you. Nonetheless I asked if someone knew the damn pipe and I certainly did not ask for smartassery or underhanded comments, no idea why you need to be told this. Great way to waste both our time.
    • As useful as you explaining what forgery is... But then again, I wasn't aware your inspectors were also forensic experts and inspect nameplates on each component to confirm everything is original. They must inspect roughly 3 cars a year at that rate. You're right though, my comment doesn't help you in anyway, so I'll go talk to my wall now. Cheers. 
    • Say that to the guy that is going to fail your inspection or tow your car for illegal exhaust modifications. If you have anything else useful to say, please go tell your wall.
    • You must be fun at parties. 
×
×
  • Create New...