Jump to content
SAU Community

Recommended Posts

Having issues with my rb20det. I'm struggling to even get it to crank. So far i've replaced the battery + starter, but when i go to try crank it struggles, similar to like what a dead battery would do

Checked the voltage on battery 13.4v, all the grounds are there. Is there something that could be draining the starter?

 

Link to comment
https://www.sau.com.au/forums/topic/480913-rb20-starting-help/
Share on other sites

"New" or "another" ie second hand?

(had a similar problem with my Pathfinder - got second hand starter, and it failed same way in four weeks!)

Does it start easier once you get it started and the engine warms up? What is the battery voltage when the engine is running?

Another thing that will cause this is a seized alternator, ac compressor or p/s pump. It will make the engine turn over much slower causing it not to start. 

I see this often on Suzuki's with seized alternators. 

Edited by TurboTapin

New, I managed to get a brand new forklift one that i've read people are running.

Doesn't start, just everytime i switch the ignition key, attempts to crank and then nothing. I'll see if i can find another alternator to try it with. 

 

I'm able to crank it by hand, and putting 12v directly to starter doesn't make any difference 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 1000ccs are side feeds but they're not currently installed, had my old factory ones in for leak testing purposes, only decided on them because front facing plenums and good top feed rail kits are out of my budget at the moment, are they really that problematic? Had a set of yellow jackets that lasted me 5 years, no real issues, only replaced them chasing this misfire issue that ended up not being ignition related 😄  
    • Are those 1000cc side feeds? If so, that's part of your problem. I have 1480cc and they idle at stoich on 98RON, and all the way to E85. Also your coil packs.....
    • Update for the sake of closure   Ended up getting the intercooler piping all sorted, new plugs and yellow jacket coils, and she was idling mint until it warmed up while I was bleeding the cooling system. Found the misfire to be localised to cyl 3 by unplugging coilpacks, ran a compression test, that checked out, then decided to get a mate to check if that spark plug was firing out of the motor. Upon cranking it over, with the injectors disconnected, the car actually fired and ran on a couple cylinders and heaps of fuel came out the top of cyl 3 I'd say that injector's either spraying incorrectly or spraying far too much, which is fine as I'm planning on replacing them anyway I'm planning on making about 250kW on flex fuel, and have a set of 1000cc injectors from ozautosport, obviously overkill but I'm planning on building the motor and running more boost further down the line, do you reckon they'd be too big for a smooth idle on 98? Thanks for the replies gents, much appreciated
    • I'm confused. You said you want to "remove the clear coat from most panels" but it sounds like you are actually doing a full respray? Few random things to add -  If you chase the blistered paint with 120 grit, I can almost guarantee you'll chase it down to bare metal (that's fine). But if you paint the car from here, you'll have nice little indents where ever the blistered paint was. The new paint won't magically level out the low areas, you need to fill them. Which leads me to the main point I wanted to add, make sure the whole car is flat before you paint it. All those areas with blistered paint you sanded out, make sure to fill them and triple check they are flat with a block guide coat. I'd also check the whole car is flat with a large block and guide coat but yeah up to you if you want to go that far.   
×
×
  • Create New...