Jump to content
SAU Community

Recommended Posts

I need help with what I should do with my diff it’s a Active LSD with a altessa pump system. It singles and I want to to double what can I do with this diff bleed it, weld it, get it shimmed, block off the altessa system? Idk what to do please help as I want to use my car for drifting / road use 

ED4A9BE0-CB2D-4F98-AC10-D1B228CC45DB.png

DA65F540-8338-471B-B2E0-B186A5B5BC89.png

Link to comment
https://www.sau.com.au/forums/topic/481063-r33-gtst-mspec-active-lsd-need-help/
Share on other sites

So you didn't go and read about the active LSD as I suggested in the other thread ? In the drivetrain section there is a whole thread stickied at the top on the thing.

1 minute ago, BK said:

So you didn't go and read about the active LSD as I suggested in the other thread ? In the drivetrain section there is a whole thread stickied at the top on the thing.

I could not find it sorry new to this site I’ll have another look

Basically you options are to bleed it and get it working back to factory 100%, or replace the entire housing, centre and driveshaft axles to go to any type of mechanical LSD. As mentioned earlier, ALL 33 and 34 GTR v spec have this type of diff too.

1 minute ago, BK said:

Basically you options are to bleed it and get it working back to factory 100%, or replace the entire housing, centre and driveshaft axles to go to any type of mechanical LSD. As mentioned ALL 33 and 34 GTR v spec have this type of diff.

Could I weld it ?

It actually astounds me that no one has ever produced a readily available LSD centre to go into the viscous LSD housing (unless I've missed something???).  A mechanical LSD diff housing is worth the GDP of a small African nation nowadays whereas a viscous LSD diff is worth a packet of Tim Tams and maybe a sneaky wristy no spit.  The person who makes it happen economically is going to make a lot of money and all of a sudden a near worthless hunk of boat anchor is worth money again!

 

If it's welded you could do nothing else as it's no going to "actuate' anything.

35 minutes ago, Shoota_77 said:

It actually astounds me that no one has ever produced a readily available LSD centre to go into the viscous LSD housing (unless I've missed something???).  A mechanical LSD diff housing is worth the GDP of a small African nation nowadays whereas a viscous LSD diff is worth a packet of Tim Tams and maybe a sneaky wristy no spit.  The person who makes it happen economically is going to make a lot of money and all of a sudden a near worthless hunk of boat anchor is worth money again!

 

I know right ? I'd be the first one to get one for the v spec !

20 minutes ago, Shoota_77 said:

It actually astounds me that no one has ever produced a readily available LSD centre to go into the viscous LSD housing (unless I've missed something???).  A mechanical LSD diff housing is worth the GDP of a small African nation nowadays whereas a viscous LSD diff is worth a packet of Tim Tams and maybe a sneaky wristy no spit.  The person who makes it happen economically is going to make a lot of money and all of a sudden a near worthless hunk of boat anchor is worth money again!

 

No. Not right.

There is little difference between VLSD and mech LSD (and in fact, the open diffs in NA cars etc) when it comes to the housing. There are literally dozens of mech LSD options for VLSD diffs. All of the usual suspects (Cusco, KAAZ, Nismo, etc etc, and many more) have mech diff replacements for VLSD and open R200 centres.

The only mech diff centres on any R chassis cars were the GTR 2-way mechanicals. And I suppose the helical diffs on some R34s can be consider mechanical too, just not in the same way. That's why they are rare and expensive.

What there is not, is something to easily put a mech centre into one of the ACTIVE diffs from the M-specs and V-spec GTRs. Because they make it difficult, and there was only a small number of them, and there are other diffs you can grab to put in their place.

  • Like 1
21 minutes ago, Shoota_77 said:

It actually astounds me that no one has ever produced a readily available LSD centre to go into the viscous LSD housing (unless I've missed something???).  

 

Wut? ..you're not including mechanicals i'm assuming.

39 minutes ago, tainer33 said:

If I welded it would I just put a bolt into the whole that the altessa bolts into?

I doubt that you could weld it. It's got hydraulic actuated clutches inside it and other shenanigans. Plugging up the hole where you pulled a hydraulic line out of it is the least of your worries!

And it is not altessa either. It's ATTESA. And what you have is not ATTESA. It is just active diff bullshit. ATTESA is 4WD. Which you don't have.

3 minutes ago, hardsteppa said:

Wut? ..you're not including mechanicals i'm assuming.

Huh??

 

3 minutes ago, hardsteppa said:

LSD centre to go into the viscous LSD housing

 

1 hour ago, Shoota_77 said:

Sorry gents, I have to clarify.  I've been talking about diffs for the GT-R.  I don't know of an aftermarket mechanical centre for those.

Yeah, but still. GTRs only have 2 sorts of diffs.

The normal one is mechanical 2-way. No reason to talk about that any more.

The other is NOT a VLSD. It is the active diff. The V-spec diff. You are right, there are no mech centres to replace those, but there's also not very many of them out there, so why would anyone bother putting the effort into developing product?

51 minutes ago, GTSBoy said:

those, but there's also not very many of them out there

I haven't looked on GTR registry for exact numbers, but that is far from correct. Off the top of my head about half of the 33 GTR is v spec with active LSD and in 34 GTR most of them have the active LSD. It is heaps rarer to have a 34 GTR with a non active mechanical LSD.

Yep, every one of these 34 GTR v spec, v spec ii,  N1, m spec and Nur spec have them. Even the halo Z tune has it, "specially tuned" as Nismo puts it.

Good in theory.

32 v specs 1 + 2 have the goods with the 31 spline mechanical LSD.

Yeah can't believe there is no a-lsd mechanical centre replacements after 25 years, they would sell like hot cakes

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey was wondering if you ended up installing the R33 GTR speed sensor - I found one too and wanted to confirm it's a direct swap into the R34 6 speed?
    • After 23 years of owning a Skyline, finally had the latch go.  Followed this guide,  works like a dream again. Great Guide 👍
    • Hi all,   I’ve got the biggest lot of problems with my R33 GTS-T   It was a freshly rebuilt 25th anniversary RB25DET (plastic cas, neo cams) probably 6 years ago now   The engine was running so well but I fkd up badly and trusted someone I’d known for 10 years that was well known around Plazmaman for his welding and fab work. I added a lovely photo of some of his previous work. Not sure why my car was worked on by whoever did this shit     I’m normally someone who would never open myself up to something like this, I still can’t believe I did it. Trusting him literally fkd it all up for me. Everything has been a struggle, like it’s almost been 6 years that’s how much I’ve just on and off been trying to work it all out.    All I wanted was a car that danced down low, like full boost from around 3~3500rpm to redline, don’t really care what power it puts down (if it ever does) but I just wanted it to be quick to get on it.    He recommended the turbo to get, I picked Hypergear but he told me to get the front 4” with a T4 and 0.68 rear housing.    I was expecting all these beautiful welds, tidy fab work and paid for it to be ready to go to a tuner when I got it back.    I got a car back that was an absolute mess, I actually couldn’t believe it was my car anymore. I don’t think you could even call what he did welds, they’re disgusting.    So I stripped everything he touched off it and with every bolt I loosened it just got worse and worse.    I covered it and literally built and finished another car in the meantime but now it’s getting to the point where I really want my Skyline back.   Its a struggle because I paid him to do all this shit because I didn’t know how to and now I’ve had to try and figure it all out omg    Please excuse the bird shit horrible welds, I’ve got my show pony car and am so beyond dealing with this car I don’t even really care at this point.    If someone told me about what he did to my car I wouldn’t have believed them but it happened to me. It was unbelievable. He went missing, my car went missing, it came back missing parts, the straight af chassis rails bore the scars of being dragged up a trailer backwards, even the sandwich plate was bent. Everything was leaking and open to whatever fell into it, rounded off/ missing bolts, power steering oil and coolant everywhere, no gaskets, parts stolen off it, even managed to damage the sump pan.   Promised me he’d finish the car, knew what it meant to me, I paid him thousands and thousands just for him to trash it. He told me he was fully licensed and insured, come to find out he’d cancelled his ABN, so obviously no insurance. I had laid up insurance on the car and would’ve been covered but I was scared they would’ve written it off or because the business was no longer trading I’d still be liable.    He was supposed to:  New fully custom mild steam pipe exhaust manifold with turbo location moved from factory position to high forward mount. (I don’t know if it is a mild steam pipe, I’ve got a funny feeling the waste gate isn’t in a very good position and I don’t think the outlets off each cylinder are equal) 4” custom stainless steel dump with external gate (he re-plumbed it) Cut and shut OEM intake manifold with throttle reposition (I ended up doing the throttle reposition) Box in pod filter (left out) New 100cel catalytic converter (pretty sure it’s there but unsure if it’s 100cel) Front mount intercooler piping fabricated to suit (all smashed up and rusty holes where he was supposed to make it look standard where fmic piping passes through. I don’t even think my front bar is going to fit 🙄) Custom 5” intake pipe from pod to turbo (didn’t come with it so had to do something to make it work with the Z32 afm)   Engine: Full cylinder head service & machining  Brand new valves Precision upgraded spring kit Engine block honed New bearings  New piston rings  New ARP conrod bolt kit New ARP head studs Cometic head gasket VRS kit   ATR43SS2 ball bearing turbo 0.68 rear housing  Turbosmart 45mm external wastegate (got delivered to the fab bloke, I’ve got no idea what spring is in it, I’m assuming the one that came pre installed) Walbro 260 fuel pump  Nismo 740cc injectors (tested to 880) Spitfire coil packs GCG FMIC RB25DET manual 5 speed 4:11 rear diff   I’ve got an Apexi Power FC in it atm, I was hoping to just get it to operating temp to make sure everything was okay before towing to a tuner but it’s over-fuelling too much. I don’t think that’s going to happen so i think I’m going to get either a Link G4 or Haltech for it. What do you guys recommend? I can’t work out the power FC so just gonna give up on that one     It’s got an exhaust leak coming from somewhere I can’t see 🙄    The fuel pressure was steady but now it like drops from 40 to 20psi randomly (noticed this yesterday)    I’ll attach pics of the shit he put on my car and the engine bay now as it sits    I really just need some help, I need a tuner in Sydney I can trust, I’d like to be with the car while it’s being tuned if possible, I know it looks terrible but unfortunately I’ve just got to put up with it for now and fix the cosmetic stuff later   Do you guys think the manifolds are going to be okay? Or do I throw the exhaust manifold and try again?   I don’t even think these combinations are going to work tbh   I know everything I fitted was rated to be able to take at least 400kW but most rated higher    If you’ve gotten this far I really really appreciate it 🙏 I don’t mind if you trash me or the car, I made a rookie error and f**k I’ve paid for it. As you’ll see 🙄  
    • From everything I’ve heard you’ll be waiting a long time for  the parts to arrive 
    • Have you looked at the workshop manual?
×
×
  • Create New...