Jump to content
SAU Community

Recommended Posts

My car has developed a whiff of burned oil note from the exhaust.

It's not not using any excessive oil or producing blue smoke, is there a way to isolate whether it's the turbo or the engine?

No oil visible on the compressor inlet. (from the engine cover vent)

Inlet manifold is clean as well.

Spark plugs look clean, compression is good on all cylinders.

Engine is almost standard with hybrid turbo and low mileage.

 

Cheers ...

 

 

 

 

 

 

 

Link to comment
https://www.sau.com.au/forums/topic/481217-a-whiff-of-burned-oil-r33gtst/
Share on other sites

What do you mean by low mileage? Has it been rebuilt, or does the odometer not show many klm (ie likely wound back)?

By this age, it would be common to have worn valve stem seals. They tend to be noticeable when first driving after the car has been sitting a while (as oil from head gets past seal into cylinder while stationary).

A compression test is the starting point to work out if you have an engine sealing problem. If there is, a leak down test can help tell you where the issue is. Turbo seals are generally not "a whiff", more like a wacky racers smoke screen

Hybrid turbo....as a general rule if you are producing more power then you will use some oil, its a fact of life.  I'm not sure where it starts to burn oil [and would change with each motor anyway] but probably around the 200-250rwkw and increases with power output.  As a rough guide 300rwkw would be approx 1/2 to 1 litre per 1000km.

  • Haha 1
  • Confused 1

Hi ..

Thanks for the replies

By low mileage I mean 86,000km! I owned the car for 12 years and the Ks are genuine.The car is sadly rarely used, I bought it with 72,000km on the clock.

It's one of the last made S2s and traffic here is so horrendous that it's mostly not worth driving in the city @ 5 - 40 km/h and zero boost.

Yes, I was thinking maybe valve stem seals but it's hard to ascertain since it's not blowing any blue smoke. If it was I could just close the throttle at higher rpm and in gear to see if anyting is being sucked into the combustion chambers via stems / seals.

I will have to take a look at the turbo's oil return feed too and also see if there's anything wrong in terms of play etc.

As for oil usage, I've driven around 1,500km and according to the dip stick there was next to no oil 'missing'

 

 

 

 

 

 

 

 

 

 

 

 

 

16 hours ago, tridentt150v said:

As a rough guide 300rwkw would be approx 1/2 to 1 litre per 1000km.

I'm almost at 300rwkw and burn zero oil. Adding 1l per 1000km you would almost do two oil changes before your oil change is actually due. I'd consider 1l per 5000kms borderline. Only time I've seen engines burn that much oil is when they were on their death bed or bubba did something funky with his crankcase ventilation or turbo oil return. 

 

Unless you swapped in a 2 stroke or a rotary, I'd look into fixing that. 

Edited by TurboTapin
  • Like 1
42 minutes ago, TurboTapin said:

Only time I've seen engines burn that much oil is when they were on their death bed or bubba did something funky with his crankcase ventilation or turbo oil return

Or....just about every modern engine with really thin, low tension rings and 0W oil.

But for an RB, agreed.

29 minutes ago, GTSBoy said:

Or....just about every modern engine with really thin, low tension rings and 0W oil.

But for an RB, agreed.

Manufacturers state normal oil consumption for warranty reasons. If any modern car was burning 1L of oil per 1000kms, they would all be bankrupt due to warranty work. Think of it, that's anywhere between 8-15L added between oil changes, depending on the manufacturer. 

 

Cheers. 

  • Like 1
1 hour ago, TurboTapin said:

Manufacturers state normal oil consumption for warranty reasons. If any modern car was burning 1L of oil per 1000kms, they would all be bankrupt due to warranty work. Think of it, that's anywhere between 8-15L added between oil changes, depending on the manufacturer. 

 

Cheers. 

Yeah. Have you heard of the Subaru FA engine? Half the Euros are just as bad. They burn more oil than the Gulf War did.

Duncan is spot on.

Cars don't like sitting. I would drive it for a bit and see if it fixes itself.. or... maybe run a good quality seal rejuvenator like the Liquid moly stop leak or something like that. then drop it out and run your normal oil and see where your at.

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next pic will probably bring back Charlie's PTSD So yes, pump is back out. I hooked the fuel return up to a hose into a container to flush out the first litre or 2, jumped the Fuel Pump relay and.......nothing.... Turns out the pump I had pulled out, checked, cleaned everything....was dead.  I hadn't actually hooked 12v to it to check it worked before I put it back in. Anyway...Neil had kept the old pump which still worked, so I just swapped it back in. All good, flushed the lines out, ready to start
    • OK....so something that works like it said on the tin! Fitting the pressure feed into the car was an absolute PITA because the oil filter is in the standard location and then there is a fitting to run to the oil cooler. On the other side between the filter and the steering box is the standard oil pressure sender (not working for some reason, something to check) and 2 tapped 1/8 BSP threads for the oil temp and pressure gauges. Unfortunately it is really tight in there and it took a hours of stuffing around to get a t fitting to connect the priming pump and retain the gauge sender.  Also, the Aeroflow sump has some massive drain plug (needs a 32mm spanner) so I couldn't use the regular fitting there either. In any case....once it was all hooked up, like magic priming.mp4 15 sec, 3 bar of oil pressure. Left it running a couple of minutes to push through everything, looked good   
    • Yeah the latest style kit has been trouble free, I've done a fair few klm on it including pushing a bit on low fuel and it hasn't been surging (that's not an endorsement for race use, I haven't tried that low, or that hard cornering!). For street use it has been a good thing, handles the high current OK, only real issue is it is not cheap
    • So, how do you feel about the Frenchys surge tank setup @Duncan? Have you had a chance to try it out more? The sketchy wiring in my fuel pump setup has decided to melt and die and I'm looking for a solid replacement now. My fuel hat is toast so the Frenchys kits providing it all look promising.
    • Yeh... literally every time i jump on a forum, see an instagram post or see an engine bay at a car show, i get an idea and add it to my 'to do' list. So what started off as, hey can u just make a couple of intake hard pipes because my dumbass bought the wrong apexi kit, blew out into a 2 week job including braided brake lines & custom bash kit for the front lip haha.  Getting Luke from A4E engineering to make a full custom exhaust with a controllable aes dump valve so i can actually switch between quiet and loud, because right now its just loud all day every day. Then after that go and get the tune redone flex e85 & 98 as i get bugger all milage from e85, makes going for longer drivers difficult
×
×
  • Create New...