Jump to content
SAU Community

Recommended Posts

On my Subaru boxer engine, I had for the first time the gauge go to the high temperature a while back because i ran out of coolant I never checked it in 3 years and after 3 years it ran out lol. I had other people tell me they top of their coolant in their cars (not Subaru's) just wondering if this is normal? I guess it's always been this way. I don't see any visible leaks, possible early head gasket failure? I topped it up to the max line now, cause I think i did lose some again.

Would I have also done damage to the head gasket if I drove the car for a few minutes with it being or high temperature? (near the red)

Many cars will push a little bit more coolant out to the overflow bottle every now and then, and will lose it if the overflow overfills. Then when it cools it will pull in some of the original overflow volume, leaving you with less. If this happens a few times, it will look like it is being lost in the engine, when it's not really.

Some engines will lose some through seal leaks, drips, etc.

Subarus will usually lose it because they are shitboxes in which a blown headgasket is a matter of when, not if.

  • Haha 1
14 minutes ago, GTSBoy said:

Many cars will push a little bit more coolant out to the overflow bottle every now and then, and will lose it if the overflow overfills. Then when it cools it will pull in some of the original overflow volume, leaving you with less. If this happens a few times, it will look like it is being lost in the engine, when it's not really.

Some engines will lose some through seal leaks, drips, etc.

Subarus will usually lose it because they are shitboxes in which a blown headgasket is a matter of when, not if.

I thought subaru fixed their head gasket problems? Mine is a 2001 model. Do you think I did damage having my temperature gauge near the red? I don't think it was for more than a couple of minutes.

Nah. Subies are famous for head gaskets from the first until the last. ~2010 Forester and anything else with that woeful EJ253 or whatever the hell they call it. 130000 km + or - and they will start to weep at the gasket. Don't fix it within 15000km and it will shit the bed.

30 minutes ago, GTSBoy said:

Nah. Subies are famous for head gaskets from the first until the last. ~2010 Forester and anything else with that woeful EJ253 or whatever the hell they call it. 130000 km + or - and they will start to weep at the gasket. Don't fix it within 15000km and it will shit the bed.

lol.

4 hours ago, silviaz said:

Mine is a 2001 model

Then it has an SLS head gasket, if it was turbo it would have the MLS gasket. Back in the day retro fitting turbo gaskets would fix the problem. The cheapest and good quality H/G for Subaru is a MLS by platinum

Just now, Rusty Nuts said:

Then it has an SLS head gasket, if it was turbo it would have the MLS gasket. Back in the day retro fitting turbo gaskets would fix the problem. The cheapest and good quality H/G for Subaru is a MLS by platinum

Ah ok interesting to know. Car is very solid no mechanical issues, just was worried about this. Do have the common faulty oxygen sensor thing but hasn't affected the car at all.

18 hours ago, Rusty Nuts said:

Both of my daughter's Subaru's throw o2 sensor codes, I clear the fault and it goes away for six months or so.

I cleaned it ages ago it stopped popping up for a while but pops up every now and again.

  • 1 month later...
On 26/10/2020 at 2:14 AM, silviaz said:

I cleaned it ages ago it stopped popping up for a while but pops up every now and again.

throw a new 02 sensor on it and bin the old one. i did this and a new set of coil packs plugs, crank sensor n maf on my 05 sti first time the thing has gone 2 oil changes without a check engine light ffs. i must say the ej25 is a total snake of intertwined garbage and like to leak from valve covers etc, but around my neck of the woods great cars for our shit roads and crazy cold weather. very driveable fun cars for shit kicking. ive run 10w40 ams high zinc oil since day one and im at 175,000 miles head gaskets are fine never had an issue. the head gaskets are known for going cause most kids wack them off the limiter all day and dont know how to drive them or maintain the shit boxes.

12 minutes ago, MoMnDadGTR said:

throw a new 02 sensor on it and bin the old one. i did this and a new set of coil packs plugs, crank sensor n maf on my 05 sti first time the thing has gone 2 oil changes without a check engine light ffs. i must say the ej25 is a total snake of intertwined garbage and like to leak from valve covers etc, but around my neck of the woods great cars for our shit roads and crazy cold weather. very driveable fun cars for shit kicking. ive run 10w40 ams high zinc oil since day one and im at 175,000 miles head gaskets are fine never had an issue. the head gaskets are known for going cause most kids wack them off the limiter all day and dont know how to drive them or maintain the shit boxes.

Probably because of the cold Canadian weather it has survived. Mildura VIC yesterday reached 45 degrees celcius and it's not even summer yet!!

7 hours ago, trel said:

Probably because of the cold Canadian weather it has survived. Mildura VIC yesterday reached 45 degrees celcius and it's not even summer yet!!

mate you nailed it on the hammer I think the cool crisp air does help them out, as long as you don't cold start them all the time and plug the bitch in when she gets below zero...the overflow caps are also crap on these cars and they can loose coolant out the overflow slowly overtime.

On 10/25/2020 at 9:03 AM, Rusty Nuts said:

Both of my daughter's Subaru's throw o2 sensor codes, I clear the fault and it goes away for six months or so.

I'm presuming they're step daughters if you let them drive Subaru's. 

2 hours ago, TurboTapin said:

I'm presuming they're step daughters if you let them drive Subaru's.

I don't have my head up my arse, so after six subaru's properly serviced, NO head gasket failures, I treat my daughter's Subaru's the same way, both properly serviced, and neither driven like they are stolen. I worked for Subaru Australia as a Service Advisor for many years and was part of the works service team for the Southern Cross Rallies. Sooooo go ahead educate me about Subaru's. Eh.

  • Like 1
9 minutes ago, Rusty Nuts said:

I don't have my head up my arse, so after six subaru's properly serviced, NO head gasket failures, I treat my daughter's Subaru's the same way, both properly serviced, and neither driven like they are stolen. I worked for Subaru Australia as a Service Advisor for many years and was part of the works service team for the Southern Cross Rallies. Sooooo go ahead educate me about Subaru's. Eh.

Oki doke, I was just trying to be funny. Nothing else. Cheers.  

Edited by TurboTapin
On 01/12/2020 at 10:11 AM, TurboTapin said:

I'm presuming they're step daughters if you let them drive Subaru's. 

Off topic: Might be a regional thing, but I never got this step- and redhead/ginger stick/shit that people throw.

19 hours ago, niZmO_Man said:

Off topic: Might be a regional thing, but I never got this step- and redhead/ginger stick/shit that people throw.

Huh? What do step children and red heads have in common? Sorry I'm not following. I'm an Irish/scot runt and I've never heard the term ginger stick before. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update: I got the magnet out. I bought 3 different flexible magnetic reach tools, but none of them worked. The magnet on the tip was all less than 2lbs of force, so i had to buy a special cylindrical magnet that had a pull force of 9lbs.  The magnet finally came in the mail yesterday, so i got under the car to get to work. The super strong magnet isn't that long, so i only have about 1 finger pinch lengths to hold it. I was so scared when i was going in the hole, that the 9lb magnet would just fly away inside the oil pan never to be seen again, but i had my butt cheeks clenched and finger gripped on that thing so tight, i managed to get it to suck the other magnet out.  It was a victory for me last night.         
    • Yep, pretty much what you said is a good summary. The aftermarket thing just attached to the rim, then has two lines out to valve stems, one to inner wheel, one to outer wheel. Some of the systems even start to air up as you head towards highway speed. IE, you're in the logging tracks, then as speeds increase it knows you're on tarmac and airs up so the driver doesn't even have to remember. I bet the ones that need driver intervention to air up end up seeing a lot more tyre wear from "forest pressures" in use on the highway!
    • Yes, but you need to do these type certifications for tuning parts. That is the absurd part here. Meaning tuning parts are very costly (generally speaking) as well as the technical test documentation for say a turbo swap with more power. It just makes modifying everything crazy expensive and complicated. That bracket has been lost in translation many years ago I assume, it was not there.
    • Hahaha, yeah.... not what you'd call a tamper-proof design.... but yes, with the truck setup, the lines are always connected, but typically they sit just inside the plane of the rear metal mudguards, so if you clear the guards you clear the lines as well. Not rogue 4WD tracks with tree branches and bushes everywhere, ready to hook-up an air hose. You can do it externally like a mod, but dedicated setups air-pressurize the undriven hubs, and on driven axles you can do the same thing, or pressurize the axles (lots of designs out there for this idea)... https://www.trtaustralia.com.au/traction-air-cti-system/  for example.... ..the trouble I've got here... wrt the bimmer ad... is the last bit...they don't want to show it spinning, do they.... give all the illusion that things are moving...but no...and what the hell tyre profile is that?...25??? ...far kernel, rims would be dead inside 10klms on most roads around here.... 😃
    • You're just describing how type certification works. Personally I would be shocked to discover that catalytic converter is not in the stock mounting position. Is there a bracket on the transfer case holding the catalytic converter and front pipe together? If so, it should be in stock position. 
×
×
  • Create New...