Jump to content
SAU Community

R33 gtst Gearbox questions

CEF33Y
 Share

Recommended Posts

CEF33Y Experienced

CEF33Y

Posted
Posted

Hey guys, so in the middle of pulling apart my R33 gearbox.

It was noisy in first and second gear, third and forth noise pretty much goes away.

I’m up to pulling speedo drive sleeve off, but have to modify my puller set to fit, so it’s not fully pulled down yet. 

The question I have for now, the input shaft bearing and the bigger bearing in the centre plate are rubber sealed bearings.

Now, from all the googling I’ve done, I’ve not come across any pics of sealed bearings. 

I would have thought the bearings need to be open to ensure adequate lubrication. I mean, the factory Nissan bearing is open...

The input bearing feels ok by hand, keen to see what the one in the center plate feels like.

Any gearbox guru’s have any thoughts on the use of sealed bearings?

 

cheers

Link to comment
https://www.sau.com.au/forums/topic/481738-r33-gtst-gearbox-questions/
Share on other sites
  • 3 weeks later...
  • 3 weeks later...
CEF33Y Experienced

CEF33Y

Posted
  • Author
Posted

Bit late to reply, But yeah, the CBC kit I got came with the sealed bearings, on which I've removed the seals.

Just got it back together last night, hope to have it back in the car tomorrow. Pretty happy with the CBC kit, even came with 1st gear bush (which looked average on mine, burred on the edge where it looks like they've used an ill fitting pipe to drive it on). Someone has had this apart before and did a average job putting it back together.

The needle bearings on 1st and 2nd gear felt terrible as I was pulling it down, and popped the seal off the (old) bearing in the center plate and there was alot of black deposit, and the oil in there was much darker than the oil drained from the Gbox.

 

Anyway, will see if the gbox noise has gone soon enough!

  • Like 1
admS15 Grand Master

admS15

Posted
Posted
4 hours ago, hardsteppa said:

got to say, they are a fairly noisy box IMO . Still hear alot of operating noise from mine even after the full rebuild, but have come to love it 😛

Couldn't agree more. After going from a 22 year old box to a brand new one, it wasn't quieter at all to the ear. 

Yes that's right, wasn't (past tense). Said new box went to gearbox heaven prematurely. 

CEF33Y Experienced

CEF33Y

Posted
  • Author
Posted

Hey guys, feel free to add any info to the thread if you feel its relevant, thats the best part about forums.

 

So, updating, as the box is back in the car, and to give the thread some closure.

Much anticipation I started car, and slowly released clutch, aaaand the noise is still there. Bugger. Probably a bit better, but hasn't "fixed" the noise.

So ultimately its got to be the gearset.

I also put a new syncro in 2nd gear, and the shift into second feels better, so along with the experience of actually rebuilding a box, it wasn't a complete waste of time (pretty close though, haha).

 

Plan from here is to keep driving/drifting with this box until it lets go, then probably buy new. I don't think "low km second hand" boxes exist anymore. And I'm not making the power where I think a gearset is warranted.

 

Thanks for the advice/help guys

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • soviet_merlin
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By soviet_merlin · Posted

      Hmmm, what do you mean by getting weaker? And where did you get that test done? I've been wondering about my battery because the cold starts crank super slowly. The voltage is fine. Not sure if cranking amps can be checked at home. Battery is 4+ years old.
    • GTSBoy
      Another "where do these lines and plugs go" RB25DET question

      By GTSBoy · Posted

      No. The simplest wastegate hookup, with no solenoid or other form of "boost control" (ie, control over your boost control, if you know what I mean) is a single hose, direct from the turbo outlet/hot pipe, straight and only to the wastegate actuator. It is that pressure signal that drives the wastegate to open, providing the boost control (and by "boost control" here, I mean, limiting how high it can go, which is essentially the spring pressure of the actuator). You only end up with tee pieces and alternate flow paths once you start adding things to the boost control system to allow you to determine how much of that boost signal makes it to the actuator. There are so many ways to do that that there is no single way to run the hoses and tees and the like. If you have a stock boost solenoid, then all it does is either allow all the boost signal to go to the actuator, or open up to allow some of it to bleed off. There needs to be a restriction in that bleeder to allow only a small amount to bleed off. And in a stock system, that would then be plumbed back to the turbo inlet (for "emissions control" reasons). That is actually what that nipple on your BOV return pipe could/would be for. If you have an aftermarket boost controller and solenoid, then the above is mostly true, but there is no need for a restrictor in the bleed, because the solenoid is pulse width modulated to create a variable bleed off. The air that escapes from the bleed can either be vented, or also returned to the turbo inlet. For emissions reasons it should be returned to inlet, but the amount of air being vented is so small that it really doesn't matter (either from an emissions perspective, or from an air-fuel ratio affecting perspective).
    • MBS206
      R32 Gtr Long Term Love, Now Project

      By MBS206 · Posted

      And other times you just need to go buy bigger injectors?
    • thatjawncrazy
      Another "where do these lines and plugs go" RB25DET question

      By thatjawncrazy · Posted

      Yup. I actually just blew my turbo. LOL.  should have checked this thread before today. i also have no boost solenoid. so it should be...one line from wastegate to turbo inlet, and a T somewhere in that line that connects to the wastegate return pipe?
    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      It's recommended, however I can assure you a good amount of people don't bother. FWIW, the OEM battery lasted 4.5 years and I changed it prematurely too, I reckon could have stretched it to 5 years.
×
×
  • Create New...