Jump to content
SAU Community

maintenance before start up (car hasn't been driven in 12 months)


Recommended Posts

haven't driven my car for a year

pretty much impossible to get it towed (stored in an underground car park) I'll have to check its actually still there.

recommendations on servicing so i can get it running safely so i can get it to a mechanic?

i couldnt be bothered changing all fluids etc. Mechanic is a 5 min drive away.

 

Edited by defari

Fuel will be sh!t....may not even fire on the fuel you have in it, it depends on the motor.  I have had it not start [replaced fuel with fresh stuff and it worked fine] but have also had another motor start fine after sitting for 18 months.  So cross your fingers and see?

7 minutes ago, defari said:

Battery is long dead.

Going to drain fuel tank + put in some fresh fuel. 

Is it worth doing oil / rad fluid change if its going to a mechanic only a few km's away?

Car is a 1999 sti wrx.

If the mec is 10 minutes away I would just put some engine and radiator flush through it for the drive to the mec, then get them to change every oil and fluid

I would pull the plugs for the first turnover to build some oil pressure, after sitting around for 12 months there isn't going to be much oil in it, apart from the sump.

Wait, it a boxer, LOL, bugger pulling the plugs, does it have the "flooded" engine thingie where if you hold your foot flat on the accelerator it doesn't start, if so do that a few times.

3 hours ago, mlr said:

does it have the "flooded" engine thingie where if you hold your foot flat on the accelerator it doesn't start, if so do that a few times.

I love that advice as it is either good and prudent to allow oil pressure to build or it will start and rev its guts out!

1 hour ago, Ben C34 said:

I love that advice as it is either good and prudent to allow oil pressure to build or it will start and rev its guts out!

LOL, yeah, it's a hit or miss kinda thing

19 hours ago, mlr said:

If the mec is 10 minutes away I would just put some engine and radiator flush through it for the drive to the mec, then get them to change every oil and fluid

I would pull the plugs for the first turnover to build some oil pressure, after sitting around for 12 months there isn't going to be much oil in it, apart from the sump.

Wait, it a boxer, LOL, bugger pulling the plugs, does it have the "flooded" engine thingie where if you hold your foot flat on the accelerator it doesn't start, if so do that a few times.

flooded engine thingie? I wouldnt know.

 

 

49 minutes ago, defari said:

flooded engine thingie? I wouldnt know.

 

 

It is a function that most EFI cars have

Both my 2015 STI and my 2017 86 had it, from googling Subaru has had this thingie for years

My 2002 Dunnydoore has it

Basically you hold the pedal down, then try and crank the car, the FI system recognises WOT with the car off, this engages the "flooded engine" mode, and shuts off the injectors while it cranks over

After a oil change I usually give it 2 or 3 hits for about 5 seconds each, with the plugs in it doesn't really turn over that fast, but with the plugs removed it turns over much much quicker

Be aware that if you crank it for more than 10 seconds the car may start, but after 10 seconds of cranking the oil should be feed around all the oily bits

27 minutes ago, mlr said:

It is a function that most EFI cars have

Both my 2015 STI and my 2017 86 had it, from googling Subaru has had this thingie for years

My 2002 Dunnydoore has it

Basically you hold the pedal down, then try and crank the car, the FI system recognises WOT with the car off, this engages the "flooded engine" mode, and shuts off the injectors while it cranks over

After a oil change I usually give it 2 or 3 hits for about 5 seconds each, with the plugs in it doesn't really turn over that fast, but with the plugs removed it turns over much much quicker

Be aware that if you crank it for more than 10 seconds the car may start, but after 10 seconds of cranking the oil should be feed around all the oily bits

ahh ok i see.

like you mentioned, i was concerned about the oil situation.

cheers for the info.

 

Edited by defari

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The smart thing is to actually locate the pump at the right point down the hanger, so that the strainer can stay sticking out at a right angle, but near the bottom. This is the perpetual hassle with retrofitting any different pump to the factory hanger. Some just go where you need it to, some need fiddling and faffing, and modifying of stuff.
    • Some updates. After a lot of praying and some inspecting of crank threads, we've found that they were both kinda munted but nothing seemed terminal. The other option was drilling and helicoiling the crank. That is obviously the last option so we decided to at least try to get a OEM GM bolt in to GM Specs. So after honing/linishing the balancer from it's .002" interference fit to a .0018" to .0015" to .0013" it eventually slotted on to the crank. ATI state the interference is nominally 0.0007-0.0009... so it's still snugger than ATI reckon and explains the issues we had to fit the thing to begin with. New GM bolt went in at 37 ft/lb then torqued 140 degrees after which was EXTREMELY   but it tightened up to 140 degrees and it was a lot of force. So all things considered, the balancer is secured to the exact specs that GM want with the OEM Stretch bolt, (that ATI say you can use..) and the balancer itself is seated and snug AF. So WOO. Engine is now back in the car with lots of swearing. Bellhousing bolts done up, driver side manifold is on, AC Compressor and hard lines are back on the car. Next step will be to connect various engine bits/wiring/intake/radiator etc. Then oil and coolant and ... test start it? And of course, looking into this issue... which actually doesn't look so bad - It looks like it can be twisted back into shape with a set of multigrips. Anyone wanna buy my bonnet? Boy it looks good over there and sunk cost sucks.
    • Also this may be a stupid question, but how would you recommend getting the strainer on a downwards angle ? as they tend to obviously clip to the bottom of the pump which usually sits level 🥴
    • Most of the R33 GTST S1 are all like "airbag? What airbag?!"
×
×
  • Create New...