Jump to content
SAU Community

maintenance before start up (car hasn't been driven in 12 months)


Recommended Posts

haven't driven my car for a year

pretty much impossible to get it towed (stored in an underground car park) I'll have to check its actually still there.

recommendations on servicing so i can get it running safely so i can get it to a mechanic?

i couldnt be bothered changing all fluids etc. Mechanic is a 5 min drive away.

 

Edited by defari

Fuel will be sh!t....may not even fire on the fuel you have in it, it depends on the motor.  I have had it not start [replaced fuel with fresh stuff and it worked fine] but have also had another motor start fine after sitting for 18 months.  So cross your fingers and see?

7 minutes ago, defari said:

Battery is long dead.

Going to drain fuel tank + put in some fresh fuel. 

Is it worth doing oil / rad fluid change if its going to a mechanic only a few km's away?

Car is a 1999 sti wrx.

If the mec is 10 minutes away I would just put some engine and radiator flush through it for the drive to the mec, then get them to change every oil and fluid

I would pull the plugs for the first turnover to build some oil pressure, after sitting around for 12 months there isn't going to be much oil in it, apart from the sump.

Wait, it a boxer, LOL, bugger pulling the plugs, does it have the "flooded" engine thingie where if you hold your foot flat on the accelerator it doesn't start, if so do that a few times.

3 hours ago, mlr said:

does it have the "flooded" engine thingie where if you hold your foot flat on the accelerator it doesn't start, if so do that a few times.

I love that advice as it is either good and prudent to allow oil pressure to build or it will start and rev its guts out!

1 hour ago, Ben C34 said:

I love that advice as it is either good and prudent to allow oil pressure to build or it will start and rev its guts out!

LOL, yeah, it's a hit or miss kinda thing

19 hours ago, mlr said:

If the mec is 10 minutes away I would just put some engine and radiator flush through it for the drive to the mec, then get them to change every oil and fluid

I would pull the plugs for the first turnover to build some oil pressure, after sitting around for 12 months there isn't going to be much oil in it, apart from the sump.

Wait, it a boxer, LOL, bugger pulling the plugs, does it have the "flooded" engine thingie where if you hold your foot flat on the accelerator it doesn't start, if so do that a few times.

flooded engine thingie? I wouldnt know.

 

 

49 minutes ago, defari said:

flooded engine thingie? I wouldnt know.

 

 

It is a function that most EFI cars have

Both my 2015 STI and my 2017 86 had it, from googling Subaru has had this thingie for years

My 2002 Dunnydoore has it

Basically you hold the pedal down, then try and crank the car, the FI system recognises WOT with the car off, this engages the "flooded engine" mode, and shuts off the injectors while it cranks over

After a oil change I usually give it 2 or 3 hits for about 5 seconds each, with the plugs in it doesn't really turn over that fast, but with the plugs removed it turns over much much quicker

Be aware that if you crank it for more than 10 seconds the car may start, but after 10 seconds of cranking the oil should be feed around all the oily bits

27 minutes ago, mlr said:

It is a function that most EFI cars have

Both my 2015 STI and my 2017 86 had it, from googling Subaru has had this thingie for years

My 2002 Dunnydoore has it

Basically you hold the pedal down, then try and crank the car, the FI system recognises WOT with the car off, this engages the "flooded engine" mode, and shuts off the injectors while it cranks over

After a oil change I usually give it 2 or 3 hits for about 5 seconds each, with the plugs in it doesn't really turn over that fast, but with the plugs removed it turns over much much quicker

Be aware that if you crank it for more than 10 seconds the car may start, but after 10 seconds of cranking the oil should be feed around all the oily bits

ahh ok i see.

like you mentioned, i was concerned about the oil situation.

cheers for the info.

 

Edited by defari

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
    • Oh yes done this when the window started flopping around.  Turns out the guides that run along the rail chanel had crumbed way. Took off the door card and pulled out the window mech, then the window, which you have to pull out through the top. As said unbolt the guide rail and don't spend 30 minutes getting frustrated trying to find a way to slide it out upwards cause that don't frigging work. Drop it down and out through the door hole. All I did to repair it was slice some 10mm clear plastic tube, vertically, then screw it to the guide rail both sides. This tubing rolls inward on both sides and leaves a gap wide enough to hold the window. To finish all I did was lube the plastic tube with olive oil and Bob's your uncle . . . well if he has the operation he can be your Aunt ! !  10 bucks in plastic tube and another 5 minute job done again . . . . YEH BULLSH#T ! My love for Skylines knows no bounds !
    • So was there a solution to this problem? I’m having this issue now. 
    • not expensive, just irreplaceable if you don't go sub 60 at wakie in that thing people will start talking
    • I haven't replaced that, but I have had the doors apart on the r32 a couple of times The door skin will be held on by a combination of clips and bolts, just take it slowly and make sure all the sneaky hidden bolts are out Once the skin is off you should be able to pop that piece off pretty easily, looks like there are only 2 bolts holding it on
×
×
  • Create New...