Jump to content
SAU Community

brake master cylinder leaking 32 GTR

DanGTR32
 Share

Recommended Posts

DanGTR32 Rookie

DanGTR32

Posted
Posted (edited)

G'day everyone 

A while ago I've noticed my R32 GTR's brake cylinder is leaking where it meets the brake booster.(non Brembo brakes)
Do you recommend rebuilding/resleeving at a brake shop? Buy an identical new one? or do I step it up a notch to a bigger one (R34 GTR etc...)? Ideally a straight swap over without any modifications would be good.
Non track but heavy duty street use car so good braking is a must.👍

Cheers.


125345269_785981592246696_261993058941255736_n.thumb.jpg.b63cde3117bd62ee7a4b23a3c204d261.jpg.de46a2550c6d3a5e6a3fd04e0daaf419.jpg

Edited by DanGTR32
Duncan Grand Master

Duncan

Posted
Posted

Don't worry about your master cylinder, your throttle cable isn't secured properly!

 

When I replaced mine r32 masters were not available new (they may be again now), I fitted a 33 gtr one and have gone without the low fluid light as the plug is different. Otherwise it is a direct fit.

No need to change the size of the standard master cylinder, even if you have somewhat larger than stock calipers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • hypergear
      Hypergear Turbochargers and High flow Services Development thread

      By hypergear · Posted

      Sharing results from recent Liberty Walk R35 GTR, since they are still considered as somesort of a V36 Skyline. We do them turbos too. This are high flowed SS-1 models with ball bearing conversion done.  Car have managed to pull 485awkws @ 20Psi so far pushing limitations of factory built engine. The build list for R35 GTR enthusiasts as follow : HyperGear high flowed stock turbos in SS1 (G25-660 specs) Custom titanium intake pipes. Vspec performance titanium front pipes. Vspec performance 4" titanium exhaust. Upgrade fuel pumps. 1200cc injectors. Ignition coilpacks Hks intake plenum. Hks intercooler piping. Greddy intercooler. Greddy bovs. Top-secret coolant reservoir. Emtron ecu. Straight E85. Built gear box.  
    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      Nah no bearings, just slip fit.  Would be a reasonably challenging but not impossible job to modify it to run bearings but I'm hoping that's not necessary as I may have well built one myself if I end up spending hours modifying it!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Brumbys with good shells are bloody expensive, I've looked at 2 "cheaper" cars, and walked away from both,  plus after some research spare parts are fairly sparce I'm starting to think that I missed the boat on finding a clean one that is straight (ish) and without alot rust I'm starting to think about a old Hilux as panels and other parts are much more available as they sold tens of thousands of them I use to be indecisive but now I'm not sure
    • soviet_merlin
      NC MX5

      By soviet_merlin · Posted

      A Brumby would probably fit a big metal toolbox in the back... this is how it begins  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Picked up a new OEM boot seal for the MX5 today as the old one got ripped a bit by me being a idiot by seeing if I could fit a large metal tool box in it, it didn't fit, and ripped the seal with the corner of the tool box I am still waiting on time to get the cams and new balancer installed, as well as the repairs to the boot Time will not be an issue soon though
×
×
  • Create New...