Jump to content
SAU Community

Recommended Posts

Hi folks, I hope to get some tips on removing front windscreen molding.

The top horizontal molding on my R32 has faded, so I order a new one.  Then I found out afterward the side vertical moldings need to come off before the top one can be removed.  Are there tricks or tips to remove the side moldings and reuse them again?  

Thanks in advance.

Yes I read that already, a few times actually, but it's just not that clear.  I mean, have you actually read it or you just copy and paste?

"disengage fastener from side molding by sliding lower two side molding clips" - I don't get it. Does that mean pushing the clips downward until they slide out from the bottom corner of windscreen? Also, there are 4 clips on each side according to the graph, so leave the upper two in place?

"remove side molding from fastener by pulling out lower end of molding" - Also don't get it. After the bottom 2 clips are out, I start pulling the side molding down? The top of side molding are 90 degree, won't that bend the molding by pulling down?

 

Given that the clips snap into place when installing, I'm pretty sure that they don't come out from under the trim. I think the sliding movement to release them just squishes them so that they flex and their tangs come out from under the lip they hook onto.

I've had them off about 20 years ago. Just fiddled around with the screwdriver until they released.

2 hours ago, TXSquirrel said:

"disengage fastener from side molding by sliding lower two side molding clips"

Unfortunately terminology is the likely problem here, I think, not to mention the GTR manual is translated from the Japanese and there is some 'JapLish' resulting.   The 'fastener' (PN 72725-04U19) referred to is a molded 'channel' that surrounds the left, right and top of the screen.   The fastener's purpose is to hold the windscreen molds in place via the clips mentioned.  It is embedded into the polyurethane windscreen seal at the time of windscreen installation.    

The clips have to be released from the fastener to take off the molds and the recommended method is using a shaped screwdriver between the mold and the windscreen to release the clips.     My interpretation is that the 'sliding' reference is actually to  'sliding' the screwdriver under the mold to release the clips.

In the same way, the 'pulling out lower end of molding' is actually a reference to moving the bottom part of the mold away from the windscreen after the clips have been released.    That has to be done carefully as to no bend the mold.     The mold could then be released at the top.

Anyway, having actually attempted this years ago I can say it's extremely difficult to release the clips without breaking them.     Unfortunately, the clips are no longer available from Nissan spare parts other than by buying a complete mold set.   They are available via the Heritage program, but quite expensive.

I bought complete new molding sets (front and rear) before the price went crazy and they've literally just been installed in my car.

 

 

    

 

 

Screen Shot 2021-04-01 at 4.27.57 pm.png

Thank you all for the feedback.  I bought the top molding first then read the manual, that's when I went oops. 

I thought I was being clever and saved money to find a website selling only the top molding, but looks I still need the whole molding kit so I wasted more money instead.  Just that my two side moldings are still in really good shape, so I'm spending extra money solely for the damn clips.

11 minutes ago, GTSBoy said:

No more than 4 years ago.

I bought my current GT-R in 2015. I reckon every piece of vinyl and plastic that I have bought since then has cost a comparative fortune.

So, six years?

Kudos sell the entire front screen trim and seal kit. I have done it and it's a pain in the arse. You will absolutely not save all of the coloured clips under the side trims - they will be brittle and just snap.

On 04/04/2021 at 8:28 AM, GTSBoy said:

Maybe.

I bought inner and outer door window strips for not too much not too long ago (like <2 yrs). Door hinges are still only ~$30 trade.

Inner door strips for white 32 arrived today. They are about $90 - $100 each.

It's the upper outer weatherstrips that are killer at over $1400 a side....Fk that !

  • 4 months later...
On 8/31/2021 at 5:08 PM, TXSquirrel said:

Can you please share how you did it?  

My molding was rock hard from age so I cut it in half somewhere in the center with an xacto knife, being careful not to destroy the molding fastener under. I then proceed to pull it out starting at the center working my way towards the side molding. If you look at your new molding, you'll notice that there's nothing that actually holds it into the fastener under the side moldings. Repeat with second part. 

If this is the first time you change a molding on your R32 or any older car, use a heat gun to soften it up as you pull it out. If you don't, it will tear often and you will need to remove the broken parts afterwards out of the molding fastener which is a pain. If you don't have a heat gun, just leave it out in the sun. I also put masking tape on the painted edge to protect it. Cheers. 

Edited by TurboTapin
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've owned a few scooters over the years, a Vespa PX oil burner was my first scooter, followed by a few others, including a little 50cc BeeWee that I used as a barracks bike, and I've had a blast on all of them, they really are the cheapest for of city/suburb transport around The only issue with scooters in Australia is lots of people look down on them due to their size,  maybe they need a big bike to make up for something else where they are lacking, unlike Europe and Asia where every man an their dog owns one, and now that filtering is legal in NSW, local traffic is never a issue Not to say I haven't owned my share of big cc bikes over the years, but they were for more blasting through the hills or Hwy riding where it needed to sit on Hwy speeds Safety wise, I ride like everyone is always trying to kill me, everyone is running a red, or running stop/give way signs, or generally asleep at the wheel, which most people are duringtheir commute, I also ride really safe, and give myself, and everyone else enough room in case I need to pull some hasty evasive actions, I've done a few rider training days over the years, which has come in handy on more than a few occasions  As for mods, there's nothing really, and yes your right about aftermarket exhaust, all you get is loud and obnoxious noises from them, like every 250-300 cc you hear with a aftermarket muffler, in saying this I did put a rear muffler from a 125 Aprilla on one of my old 125 scooters, it was horrendous and no amount of full face helmet and ear plugs would dampen that noise As for coming from the Harley, and what a overpriced POS that was, I no longer do big rides as my poor old busted joints ache after about 1/2 an hour of riding, long cruises are so much more enjoyable now in a car, so a big bike would be pointless   
    • Oh wow, it's easy to forget how cheap these can be. Probably the cheapest way to travel. Though people in cars here tend to be morons and I would not feel very safe. Were scooters ever big in Australia? It used to be the thing growing up in Europe ~20 years ago. 50/70/125ccm Peugeot or Yamaha and some others. Utterly obnoxious Polini race exhausts. Kick stands that slant as much as possible. So loud. So much noise for really not moving very fast at all. But it felt cool at the time. Not sure where I'm going with this, but there is an aftermarket for mopeds! Though I'd have pictured you more for a Goldwing kind of guy after growing out of the Harley.
    • You need to know I am sorry for this.  
    • As the MX5 isn't apparently "manly" enough, and I need something for runs to the local shops, and also take to my part time job at the salon, basically I can keep the MX5 away from car parks and stuff......like "flying lockers", I was wondering what I could buy to fix this issue LOL, I pick up a new Yamaha 125 Delight this arvo from Trooper Lu, basically a R1 that you can fit a slab of beer on between your feet, also, it was $29400 cheaper than a R1, so actually it's 2 x better than a R1    
    • Nah. H2S. H2S is "rotten egg gas", which is what is associated with no cat. SO2 is equally nasty, and if you've ever smelt it you'll know all about it. More of a choking, acid in the back of the throat sort of thing. But you can only smell it in a narrow range up to about 1ppm. Above that, it irritates your mucous membranes, but you don't smell it.
×
×
  • Create New...