Jump to content
SAU Community

Recommended Posts

Hi all,

I got an alignment today to coincide with getting the tension rods replaced and the steering pulling to the left.

Initially, I thought this would just be a routine alignment to go with the tension rods being replaced; however there was something weird picked-up by the shop to explain why the car was pulling to the left.  

The last alignment was  around three months ago and the toe was set at zero. I hit a sizeable bump in the road about 2 months ago but there was no noticeable steering issues immediately following this. Only recently, say a week or so after changing the tension rods did I notice the steering wheel was cocked to the right, even when there was contrarian camber in the road.

When stationary, I can feel a slight click/knock through the steering wheel when intially turning. This was actually why I changed the tension rods, well this and leaky TR bushes.

I'm sure the steering rack bushes need replacing after >200k kms but could this be the source of the problem?

As you can see, there seems to be a lateral shift in something in the front that caused the toe to move to +1.6 L/-1.5 R, you'd assume somewhere in the vicinity of the rack given the movement. I'm assuming the toe was true (@ about zero) prior to this shift.

Using my broken Japanese, I was able to figure out the mechanic was saying "the alignment is fine now but it will change again when subject to certain lateral forces", "something something steering rack something" - I couldnt figure out whether he was saying bush or something else here.

I should note that I've recently tried (with my hands) to move the front wheels with the car in the air but it felt solid.

S__19980291.thumb.jpg.c727cd980dd6997211a88e4812be17cc.jpg

Three options for an impact caused change of toe in the same direction on both sides;

  • Bent tie rod. Less likely because of even change on both sides, but possible.
  • Steering rack moved on its mounts towards one side.
  • Crossmember moved on its chassis mounts to one side. Less likely than the steering rack, because it is more heavily attached to the chassis (than the rack is to the crossmember), and also, the rack would move with the crossmember, so probably wouldn't turn up as the change you've seen. It is not impossible to actually move the crossmember though. I had an incident in my car with a gutter that did just that.

So, yes, likely that rack bushes are in a bad way, because even if they weren't before, they would have to have suffered to permit the rack to move - unless bolts have bent.

  • Like 1
On 10/12/2021 at 3:11 PM, GTSBoy said:

Three options for an impact caused change of toe in the same direction on both sides;

  • Bent tie rod. Less likely because of even change on both sides, but possible.
  • Steering rack moved on its mounts towards one side.
  • Crossmember moved on its chassis mounts to one side. Less likely than the steering rack, because it is more heavily attached to the chassis (than the rack is to the crossmember), and also, the rack would move with the crossmember, so probably wouldn't turn up as the change you've seen. It is not impossible to actually move the crossmember though. I had an incident in my car with a gutter that did just that.

So, yes, likely that rack bushes are in a bad way, because even if they weren't before, they would have to have suffered to permit the rack to move - unless bolts have bent.

Thanks as always GTSBoy.

I am just trying to figure out what the hypothesis is here, just in case I'm missing something. I'm going to have to wait a week or so until I can use the lift at the local shop so its good to gather a list of potential failure items. 

Rack bushes have been ordered. I'm going to assume the crossmember is okay but will give it a thorough check when the car is on the lift. I'll document my findings here for anyone else in the same position.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
    • Thanks Paul I reached out to Autotainment but they no longer work on JDM cars as the guy who used to do the work moved on and is no longer doing that kind of work. I am talking with Level Up Audio though.
×
×
  • Create New...