Jump to content
SAU Community

Rb25det correct timing angle

Tomak

By Tomak,
in Engines & Forced Induction

 Share

Recommended Posts

GTSBoy Grand Master

GTSBoy

Posted
Posted

Actually, I just realised that you were talking about a Link. What I said could still be true, but because it is an aftermarket ECU with quite  few things that you could have wrong (either in the ECU or out in the hardware), it's pretty well impossible to do other than guess what is going on.

Tomak Collaborator

Tomak

Posted
  • Author
Posted
On 05/12/2021 at 1:37 PM, GTSBoy said:

It is doing that because the ECU is retarding timing to try to pull the idle revs back down. This suggests that your idle control motor is not working.

I personally have posted many thousands of words on this subject. Go searching.

 

i mean how to set up the crank angle sensor, what deegrees it should be on crank pulley using strobe light.....? That was my question

CAS.thumb.jpg.2dba0931208f17bb2c8d5faa3ca5b77e.jpg

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

You need to lock the timing in the Link ECU then sync it, then unlock it.

It could be pulling timing on idle as part of the idle strategy.

Also if the car is running fine, don't touch it. Your tuner may have tuned the car with timing out so the entire map has been offset by that.

  • Like 2
robbo_rb180 Grand Master

robbo_rb180

Posted
Posted

Base timing offset will need to be checked. Link help file in the pc link software has the procedure in there.

I've set my link ecu up for 15 degrees base timing and have an idle ignition map as that could be something that has been setup. 

If it has just started idling high start looking for leaks after the throttle body. 

Pm me your tune can see how it's been setup 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MidnightR32
      Cold compression test after rebuild... should I be worried?

      By MidnightR32 · Posted

      This is for an RB20DET. Sorry for not including that. 
    • MidnightR32
      Cold compression test after rebuild... should I be worried?

      By MidnightR32 · Posted

      Welp, this is where my compression lands after my rebuild. Thoughts? I have ~6 hours on the motor. 
    • Keeper
      SAUNSW - Cruise - Albion Park Aviation Museum - 9th August

      By Keeper · Posted

      Event details are now up!
    • GTSBoy
      Another little story of weird shit happening

      By GTSBoy · Posted

      Well, after the full circus this week (new gearbag, 14 psi actuator on, injectors and AFM upgraded, and.....turbo repair) the diagnosis on the wastegate is in. It was broken. It was broken in a really strange way. The weld that holds the lever arm onto the wastegate flapper shaft broke. Broke completely, but broke in such a way that it could go back together in the "correct" position, or it could rearrange itself somewhere else along the fracture plane and sit with the flapper not parallel to the lever. So, who knows how and when exactly what happened? No-one will ever know. Was it broken like this the first time it spat the circlip and wedged itself deep into the dump? Or was it only broken when I tried to pry it back into place? (I didn't try that hard, but who knows?). Or did it break first? Or did it break between the first and second event of wierdness? Meh. It doesn't matter now. It is welded back together. And it is now held closed by a 14 psi actuator, so...the car has been tuned with the supporting mods (and the order of operations there is that the supporting mods and dyno needed to be able to be done first before adding boost, because it was pinging on <<14 psi with the new turbo with only a 6 psi actuator). And then tuned up a bit, and with the boost controller turned off throughout that process. So it was only running WG pressure and so only hit about 15-16 psi. The turbo is still ever so slightly lazier than might be preferred - like it is still a bit on the big side for the engine. I haven't tested it on the road properly in any way - just driven it around in traffic for a half hour or so. But it is like chalk and cheese compared to what it was. Between dyno numbers and driving feedback: It makes 100 kW at 3k rpm, which is OK, could be better. That's stock 2JZ territory, or RB20 with G series 550. It actually starts building boost from 2k, which is certainly better than it did recently (with all the WG flapper bullshit). Although it's hard to remember what it was like prior to all that - it certainly seems much, much better. And that makes sense, given the WG was probably starting to blow open at anything above about 3 psi anyway (with the 6 psi actuator). It doesn't really get to "full boost" (say 16 psi) until >>4k rpm. I am hopeful that this is a feature of the lack of boost controller keeping boost pressure off the actuator, because it was turned off for the dyno and off for the drives afterward. There's more to be found here, I'm sure. It made 230 rwkW at not a lot more than 6k and held it to over 7k, so there seems to be plenty of potential to get it up to 250-260rwkW with 18 psi or so, which would be a decent effort, considering the stock sized turbo inlet pipework and AFM, and the return flow cooler. According to Tao, those things should definitely put a bit of a limit on it by that sort of number. I must stress that I have not opened the throttle 100% on the road yet - well, at least not 100% and allowed it to wind all the way up. It'll have to wait until some reasonable opportunity. I'm quite looking forward to that - it feels massively better than it has in a loooong time. It's back to its old self, plus about 20% extra powers over the best it ever did before. I'm going to get the boost controller set up to maximise spool and settle at no more than ~17 psi (for now) and then go back on the dyno to see what we can squeeze out of it. There is other interesting news too. I put together a replacement tube to fit the R35 AFM in the stock location. This is the first time the tuner has worked with one, because anyone else he has tuned for has gone from Z32 territory to aftermarket ECU. No-one has ever wanted to stay Nistuned and do what I've done. Anyway, his feedback is that the R35 AFM is super super super responsive. Tiny little changes in throttle position or load turn up immediately as a cell change on the maps. Way, way more responsive than any of the old skool AFMs. Makes it quite diffifult to tune as you have to stay right on top of that so you don't wander off the cell you wanted to tune. But it certainly seems to help with real world throttle response. That's hard to separate from all the other things that changed, but the "pedal feel" is certainly crisp.
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      I'm a bit confused by this post, so I'll address the bit I understand lol.  Use an air compressor and blow away the guide coat sanding residue. All the better if you have a moisture trap for your compressor. You'd want to do this a few times as you sand the area, you wouldn't for example sand the entire area till you think its perfect and then 'confirm' that is it by blowing away the guide coat residue.  Sand the area, blow away the guide coat residue, inspect the panel, back to sanding... rinse and repeat. 
×
×
  • Create New...