Jump to content
SAU Community

Crank angle sensor question? R33 gtst s2

Almera96gtin15
 Share

Recommended Posts

Almera96gtin15 Explorer

Almera96gtin15

Posted
Posted (edited)

I noticed that the centre of the CAS (mitsubishi symbol) is not spinning all the time and sometimes stops all together? I touched it and the symbol spins, even the engine note changes when I touch it. 

Is it faulty? As I get slight bit of a hesitation when boosting also. 

I only decided to check iacv (cleaned with brake cleaner) and check the timing as it was fluctuating on idle. 

Thanks guys. 

 

 

Edited by Almera96gtin15
TurboTapin Proficient

TurboTapin

Posted
Posted (edited)
On 4/27/2022 at 6:54 AM, Almera96gtin15 said:

Hahaha lol I don't mean that the whole CAS spins

The mitsubishi symbol in the centre of the CAS. Have a look at yours and you'll see what I mean. 

It's not a casper the friendly ghost situation lol. 

The little Mitsubishi sign in the middle of the CAS should not spin at all. It probably got loose somehow(!?) and spins here and there due to vibration. Even stranger is touching your CAS should not cause your engine to sound different, that's why Duncan is probably asking if it's loose. 

 

It's normal timing fluctuates a few degree's at idle. That's what controls your idle speed. You need to lock your timing prior to verifying. If your idle is swinging drastically, you most probably have a vacuum leak. Pressure test or smoke test your system. 

Edited by TurboTapin

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      NPboosted manifold fitting purpose

      By GTSBoy · Posted

      No. The ECU's hose is for a connetcion between the plenum (assuming single throttle body, not ITBs) and the ECU's internal MAP sensor. This is the primary load measurement of the ECU - so you need to get this one right. This has NOTHING to do with the boost contol. The wastegate also needs to see a boost signal - but it is actually far better for it NOT TO COME FROM THE PLENUM (again, assuming single TB, and not ITBs). This should come from the turbo's compressor housing (assuming there is a nipple on there, which there might well not be), or on the boost pipe somewhere between the turbo and the TB. On the pipe from the turbo to the intercooler is usually most convenient. The boost controller is then located between that boost source and the wastegate, ACCORDING TO THE CORRECT PLUMBING DRAWING FOR THAT BOOST CONTROLLER. There is no general diagram or instruction that will be correct for every case. Then the other ports on the plenum are for purposes such as Duncan described. If the boost controller has an internal MAP sensor, for a boost display, etc, then it will want to be hooked up there, alongside the ECU and the FPR.
    • eli995
      NPboosted manifold fitting purpose

      By eli995 · Posted

      Ok gotcha, so one post to fpr  another to bov  and I have the mishimoto boost controller and a link g4+ so I’d just have the tuner set it up properly. For the last two from plenum post throttle to  ecu/ boost controller, I know that I have a hose coming from the ecu that I was confused about so I assume that’s what connect to the boost controller from the ecu? And then the last is just from plenum to boost controller then to wastegate?
    • eli995
      NPboosted manifold fitting purpose

      By eli995 · Posted

    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      From there, it was just a quick electrical check, prime the oil and start her up Which, is not what happened. 1. Bloody seppo Aeropro battery holder. Not only was it too tall for the battery (which I'll forgive them for, I have another battery the same nominal size that is taller than Neil's one, but the bracket is a fixed height so the battery was spaced up) But the thing that really shits me is the hardware to hold it on requires a 7/32 Hex key. WTF. No-one will ever be able to remove or install the damn thing without a hex key they don't own 2. Kill switch no longer worked once the console was installed. Neil mentioned above he had to adjust the length but it no longer cleared the console once installed. Sorted. 3. Suspiciously, the brake light holders were hanging in the boot with no globes. Sure enough the stopper on the brake pedal was missing so they are always on unless the kill switch is activated. Will pick one up tomorrow (turns out 32 and 33 don't use the same stopper) 4. All that sorted, I turned on the kill switch, turned the key to ACC. Nothing. Turned it to IGN. Nothing. Checked some fuses and found the main IGN in the boot was missing which improved things once it was replaced. Now ECU and dash lights turn on with IGN but still no fuel pump. 5. Turned it to Start....ECU on, no fuel pump, no starter. Plus the voltage dropped straight to 9v.  I suspect the starter is f**ked but am going to have to work through it all and see what is happening, really looks like more than one issue. Does anyone have the R33 fuse box key with the circuit it sources from (eg BAT, ACC, IGN, SRT etc) and supplies? I can find a translated list showing Amps and circuit without supply circuit, and I can find supply circuit without Amps and target circuit.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      3rd time lucky, the AAC is now all plumbed up after getting some final fittings All set up under the plenum of maximum access
×
×
  • Create New...