Jump to content
SAU Community

Recommended Posts

Hi all, l didn’t want to put anything on the forum, however l am unable to work this out and am extremely frustrated, hopefully someone can give me some good direction.

the car blew a cooler hose, since then it has developed a miss at approx 5,000 rpm upwards.

the strange thing is that it now fowls only plug number 6.

all others are fine.

changed coil packs around and same issue.

new coil loom, same. Car runs, idles and drives fine, as long as you don’t go past 5.000 rpm.

running apexi fc. Has had tune. Developed this after the tune. However was running amazing until the hose blew off. 
Boost is a conservative 15.

if anyone can give me some direction it would be greatly appreciated.

regards.

 

 

 

Link to comment
https://www.sau.com.au/forums/topic/483695-r33-s15-missing-at-5000rpm-onwards/
Share on other sites

Sounds like it had a boost leak ( the cooler hose about to pop off) and was tuned to suit that. Now boost leaknis gone tune is wrong.

 

Did you pressure test the cooler pipes before the tune?

 

Yes, plugs changed, several sets now.

has had new cooler piping both sides.

turbo  side to air filter done pre tune. Intake done only a week ago. Still same problem.

 

Car ran perfect after tube, 232rwkw. @ 15psi.

drove it 250kms after tune, no issue. Gave it a few short drives and it, again, was perfect.

blew the intake pipe to plenum off. 

once this happened it ran like shit.

changed plugs as they were all Fouled. 
since then it has had the issue.

Appreciate everyone’s input.

 


 

I have seen a car foul plugs mysteriously more than others, and it turned out to be the diaphragm in the FPR that had failed, sending fuel into the plenum into two cylinders specifically.

Something mechanical has let go in the cylinder that is fouling. It would be very suprising to somehow make a tune that only fouls 1 cylinder unless you are playing with cylinder trims, which I don't think is very common on a powerFC.

You need more data available to you. Is the problem spark related? Fuel related? You may need a dyno to figure this out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are a few different ways of doing it. I'm currently running two 1000cc pre-TB nozzles and PWM the pump for control. I'll be moving over to a constant pressure system and direct port. I'll run the pump off a regular relay, have it cycle on roughly 5psi before I start injecting to build pressure and then PWM a WMI solenoid (It's basically an injector that can take a lot of pressure and not corrode with water and meth.) The solenoid feeds the 6 direct port ~200cc nozzles. I'll also keep one ~250cc pre-TB nozzle to help keep IAT's in check.  Safety will be a little different as well. I used to use a pressure switch but will be moving over to a pressure sensor between my solenoid and nozzles. I'll trigger my solenoid and if I don't see specific pressure within a specific timeframe (e.g 100psi within a second, 175psi within 2 seconds), I kill it and revert back to non WMI maps the same way I did it before with 4D in Haltech. I was just figuring out the timers in my ecu last night. They made that a little more complicated than I would have liked... I wish Haltech offered a larger set of logic/math functions like other ecu's do. I can't do very much with just AND's and OR's.  I've been asked to do fuel/ignition mapping on a medium bore engine at work in May (192L V16). Being the only programmer in my region and having went and opened my mouth about knowing the ins and outs of fuel/ignition mapping, I have now been deemed an expert. Fun fun. The entirety of the logic and algorithms are programmed in C on a PLC. As I spend more time figuring it all out, I like what I see and eventually I may consider doing the same as a pet project to replace my ecu.   
    • This would be interesting, would you feed it via a 2nd row of injectors? Or just usual WMI nozzles?
    • Cut sump up and extend. Win win 😂 
    • All, What's the recommended torque for the 1/2 head studs for RB30 twin cam conversion with RB26 head?  
    • also, we need to know which solution worked....
×
×
  • Create New...