Jump to content
SAU Community

V35 4doors 2001 - rear main seal retainer replacement - any good service in Adelaide?


Recommended Posts

Can't find a good mechanic in Adelaide to replace the main rear seal. Nissan dealer is fully booked for a next few months. The engine needs to be suspended, removal of the gear box and the oil pan to get into it (probably starter as well) and place a new gasket proper, tricky. Anyone knows a good trustworthy place where it can be done?

 

Many thanks

IMG_20221102_102958.jpg

IMG_20221102_103002.jpg

Screenshot_20221201_183801.jpg

Link to comment
Share on other sites

French??  Is there anything French on these??

Anyway, I hope you are doing more than just the rear main, you will also want the 2 seals number 11121 and 11121+A as well as dropping and re-sealing the whole upper sump (assuming that is what you are doing anyway).  Definitely not a job you want to skimp on, nothing worse than chasing new oil leaks because of something you disturbed but didn't replace in the process.

  • Like 1
Link to comment
Share on other sites

19 hours ago, sonicii said:

French??  Is there anything French on these??

These come from the era where the Nissan-Renault tie up was not doing Nissan product any favours. Started in 1999 and has made almost every Nissan since then a French influenced turd, compared to what it might have been if the insanity of the 80s and 90s had been allowed to continue (assuming that it could continue without Nissan going broke, of course).

Link to comment
Share on other sites

That might be a bit harsh.  I have had a late 80s R series skyline, a mid 90s maxima, wife had a mid 00s maxima, I had a mid 00s V35 and now a Q50.  They have been an improvement each time.  I would t go back to any given the chance..

 

I would agree, the Renault alliance didn’t do Nissan any favours, beside saving them from bankruptcy..  but Renault didn’t really have that much influence on Nissan vehicles they weren’t co-developing.

Edited by sonicii
Link to comment
Share on other sites

It's way off topic by now, but I have to agree the quality of engineering went way down hill. The level of additional power  you can make without breaking things and the general reliability under heavy use like racing of the standard parts in R chassis is very unusual.

But it did have to change, Nissan was loosing money on every car they made which is never going to last

Link to comment
Share on other sites

7 hours ago, niZmO_Man said:

It's been 10 years man, they removed Ghosn. Get over it :P

Didn't they remove him in a violin case (#yesitreallyhappened)

Anyway, those cars look nothing alike, one is white and one is silver.

It is nissan who keep copying camrys.

1990s camry wagon

1998 Nissan Stagea

mid 2010s camry hybrid sedan

06896dXcnA1628064208.jpg

  • Haha 1
Link to comment
Share on other sites

  • 9 months later...

Haha love this conversation.

holden and Toyota shared models,

Commodore/Lexon

Camry/Apolo

Daiwoo was owned by Holden

Hyundai was Nissan (I think)

Kia is owned by Ford who also own Mazda

BMW owns VW and a few other too I think.

 Nissan and Renault are apparently one of the same.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • There is a LOT of stuff that can be done, it all depends on how much time and money you want to spend on doing in.  Not all ECUs will be able to do it, and the more control you need the more time and knowledge needs to be put into making it work.  If you're willing to spend the time and money and have the right hardware and skills involved there's a lot that can be done. 
    • I am impressed with all this level of adjustment. I didn't expect all this possibility
    • Correct.  In the case of the 500kw dyno plot I showed you the car actually runs two boost control solenoids for boost control and a 5psi wastegate spring.  It allows me to control how much boost pressure is applied to both sides of the wastegate valve at any point and fairly accurately control boost target as a result. I've tuned it so that it's able to target anywhere from 5psi to 25psi depending on what's needed.  The target tables I've set up in that car are Gear vs RPM, so every gear has potential for a different boost (and torque) curve.   First and second gear have quite low boost targets, third gear actually has different target boost all the way through the rpm range as it's a stock RB25 gearbox - the boost targets have been chosen to maintain a peak of 600nm (what the owner has set as the maximum torque he's happy with putting through the stock 3rd gear) but it carries that to the rev limiter.   The boost curve to achieve that is something of a ramp up, then hold, then ramp up again and the power curve looks more like a flat line haha.  
    • so you can decrease or increase the boost depending on the diet as you wish?     by acting on the wastegate?
    • That's torque and power, it's all from a single run.  The boost curve is "held back" from it's peak target in the 3500rpm to 5000rpm range from memory, so it ramps hard to something like 18psi then climbs more progressively to 23psi nearer 5000rpm.   It makes the torque (and power) ramp more "natural" and less hard on parts and traction, it doesn't feel artificially held back.   
×
×
  • Create New...