Jump to content
SAU Community

R32 gtst frame rail bung

Prof_Finesser
 Share

Recommended Posts

Prof_Finesser Enthusiast

Prof_Finesser

Posted
Posted (edited)

Hello today I was getting little stuff done here and there getting ready for my first start and I noticed that the black piece was kind of hanging out and it was broken i must have hit it or something I put my finger in the hole that it was in and felt nothing  just wanted to see if anyone knew what this was and if I need to replace it.  It was in the hole between the two lines.

DB77B40E-2A4A-4AE6-9FE4-ADA7A00586D4.jpeg

D5B58ACA-E16F-410E-97C2-2AFE99831A28.jpeg

Edited by Prof_Finesser
Link to comment
https://www.sau.com.au/forums/topic/484257-r32-gtst-frame-rail-bung/
Share on other sites
GTSBoy Grand Master

GTSBoy

Posted
Posted

Hmm. Dunno. I can't think of a reason for something like that to be poked in that rail hole. Don't know if that thing is even on my car. I won't be near my car for another 10 days or so, so I can physically check then.

Right now I have photos on my phone from when the engine was out, but they're too dark and blurry in that corner of the bay to show whether it is there or not. Black on black hard to see even in a close up!

Prof_Finesser Enthusiast

Prof_Finesser

Posted
  • Author
Posted
5 hours ago, GTSBoy said:

Hmm. Dunno. I can't think of a reason for something like that to be poked in that rail hole. Don't know if that thing is even on my car. I won't be near my car for another 10 days or so, so I can physically check then.

Right now I have photos on my phone from when the engine was out, but they're too dark and blurry in that corner of the bay to show whether it is there or not. Black on black hard to see even in a close up!

Yea idk why it would be something like that would be in the frame rail I’m pretty sure it’s fine but I just want to double check

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Noice. Mostly.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Yuck. But it's kinda the same principle, moving timing around to make car run bad but sound good.... I went for a more spirited tuning drive to iron out a few things. Car no longer stalls, and it loved to dip RPM low when you clutch in. After tuning this (and the 4-5 tables that HPTuners/LS1 OEM ECU wants for idle air correction) it's now behaving somewhat normal. All expected because there's a new TB, new Intake manifold and that new TB which is 102mm vs 78... has an entirely different IAC passage which is smaller because ????? Unfortunately at this point I went to make further fine tuning changes to avoid it flaring up, you know... _tuning_ the HPTuners dongle died. Well to be more accurate - The USB cable died in a fashion that anyone who has ever charged a phone will recognize. After the app demanding I resync it 50 or so times (which all 'succeeded' but all failed) the device does not want to sync and I've logged a ticket with support to see if it's fixable. US Support said it was a 'storage issue' but after removing the SD card inside it and formatting it/fixing it the issue does persist. Unfortunately usually the fix is "Turn in your old dongle and pay $700 for the upgraded one" it's cheaper because I get some free licence credits I unfortunately don't need. However I'm 10 minutes down the road from HP Tuners AUS/VCM so at least I won't need to post it, and logged a new ticket for support over here. Definitely drives different. My SOTP dyno believes it's probably making 310-320kw instead of the 280 before.  It scrambles for traction a little now whereas it previously different. It drives like a bigger cam car up top even though the cam is smaller, likely due to the cam not being advanced 6 degrees. The timing is deliberately low and the fuel is very rich so who knows if this will improve on the dyno. It may, imperceptably. Also funny is removing the pineapples definitely makes the car squat more and axle tramp less. So this behavior of having more top end, squatting more, and scrabbling for traction more makes me think = more power. But I could have just been sitting on the threshold of that kind of behavior before. Time will tell if my butt dyno is calibrated right. I need the exhaust leaks fixed before dyno tune for obvious AFR related reasons - I repositioned the pipes but I'm not confident it's fully sealed even if it is better. At least the car does drive around while I cannot tweak/tune it for now. And I have aircon again. medium success!
    • GTSBoy
      I need more than help to finish my R33

      By GTSBoy · Posted

      Don't use that manifold. Please don't use that manifold. Sunk cost fallacy is not worth the later pain. None of these will be relevant to the change that will come from the different turbo and manifold. As in, the effect of the exhaust will be nil, regardless of what else is changed. And all the cam and fuel system stuff is not changing either way, so has no effect. The turbo and manifold (and to a small extent the wastegate)....big change.
    • marni
      I need more than help to finish my R33

      By marni · Posted

      Just wanted to say thank you for your input   my man (lead mechanic by trade) and I have done a heap of work as you can imagine just to make the hot side work with the dump pipe, stupid massive intake on turbo, trying to get the waste gate on was not fun.  I’m kinda getting to the point where I don’t know if I try and make this work and not throw all this cash and time away or do I scrap the lot and start again? the Apexi I’ve got was tuned for a few slight differences:   Tomei pon cams (mine are stock neo) Turbo smart 38mm external waste gate (mines 45mm replumbed) with stainless screamer pipe  3inch turbo back exhaust with high flow cat Sard 800cc top feed injectors Sard adjustable fuel pressure reg    
    • joshuaho96
      My BMW 335i

      By joshuaho96 · Posted

      Out here E90s are the cheapest way into a sporty-ish car because everyone knows just how expensive the repairs can get. 8-10k USD for an automatic 335i. 
×
×
  • Create New...