Jump to content
SAU Community

Recommended Posts

I run a 4 port solenoids, however I don't recommend it for everyone.

In the past when I could be bothered working on other people's car for beer and cash I would generally fit 3 ports sourced from efisolutions aka taarks back in the day.

https://www.efisolutions.com.au/3-port-mac-valve-boost-control-solenoid

 

2 hours ago, IM-32-FK said:

what fitting style do you use?

I actually fitted 3AN Teflon lines from the valve to the wastegate.

Had too many issues with hoses popping off at the track so full sent it with AN fittings.

 

And Birrong Automotive are great, love their RBs.

 

 

  • 3 weeks later...

just a couple more questions:

- i was the told the r32 tps is better than 33/neo tps because it has a 'longer/bigger/larger' pulse and that i should run that instead

- was also told to run a slytech 2 wire universal iacv too instead of the stock iacv on a plazmaman plenum because the coolant spring in the stock iacv can cause problems

anyone care to advise?

Not sure what ecu you have again but if it's capable, why not just go DBW throttle body. No need for iacv and probably TPS too. I'm sure @Dose Pipe Sutututu will be here in a moment to say exactly this.

  • Like 2

Throw the TPS, cable throttle, idle control valve, aux air valve out and go DBW.

I wish I did this sooner, superb idle control, no issues with big cams and AC, etc.

Not to mention you can now setup cruise control too.

 

 

 

  • Like 2
1 hour ago, Dose Pipe Sutututu said:

Throw the TPS, cable throttle, idle control valve, aux air valve out and go DBW.

I wish I did this sooner, superb idle control, no issues with big cams and AC, etc.

Not to mention you can now setup cruise control too.

 

 

 

ok i bought a plazmaman inlet with a 74 dbw, but that means i need to buy a link g4ret and also need to buy a pedal and mount so it comes down to paying like $500 more compared to throttle cable setup.

it better be worth it.

Edited by IM-32-FK
  • Like 2
7 hours ago, IM-32-FK said:

just a couple more questions:

- i was the told the r32 tps is better than 33/neo tps because it has a 'longer/bigger/larger' pulse and that i should run that instead

- was also told to run a slytech 2 wire universal iacv too instead of the stock iacv on a plazmaman plenum because the coolant spring in the stock iacv can cause problems

anyone care to advise?

WTF does that even mean? Is he talking about the deletion of the idle switch in favor of voltage-based idle detection? All standalone ECUs to my knowledge ignore physical idle switches.

If you want DBW to be worth it just add cruise control and traction control to the tune, maybe DBW-based rev limiting to get a no-compromise soft cut while you're at it. There's more you can do but those three alone are pretty big headline features you can do "for free" that are kind of a disaster to implement on traditional cable throttle. In theory you can also implement tricks like automatic rev-matching too.

  • Like 2
10 hours ago, IM-32-FK said:

ok i bought a plazmaman inlet with a 74 dbw, but that means i need to buy a link g4ret and also need to buy a pedal and mount so it comes down to paying like $500 more compared to throttle cable setup.

it better be worth it.

Nice! I’m yet to get my car with the new DBW setup tuned but already is definitely worth it! Check out www.iee.nz they have dbw pedals that fit stock location and stock pedal pads for that true OEM fit, he also has the right size rubber grommets to fill the cable hole. I wish I found them before I went the 350z pedal with adaptor route… are you keeping the factory oil/water heat exchanger?

Edited by R3N3
  • Like 1
10 hours ago, IM-32-FK said:

It better be worth it.

It is, especially when you can control the pedal curve, which cannot be done on a traditional setup unless you swap the the throttle wheels and that's still garbage because it's generally a fixed curve.

If you've ever driven a car with a large cable throttle you'll notice it's ver touchy at low RPMs, you can get rid of that behaviour with DBW and exponentially ramp in the DBW TP vs. your Accelerator Pedal Position (APP).

And lastly superior cold start, idle control.

1 hour ago, R3N3 said:

Nice! I’m yet to get my car with the new DBW setup tuned but already is definitely worth it! Check out www.iee.nz they have dbw pedals that fit stock location and stock pedal pads for that true OEM fit, he also has the right size rubber grommets to fill the cable hole. I wish I found them before I went the 350z pedal with adaptor route… are you keeping the factory oil/water heat exchanger?

so as far as im aware you can either

1- buy a bosch dbw pedal and mount it onto the chassis https://www.bosch-motorsport-shop.com.au/accelerator-pedal-module

2- Buy an adapter plate that lets you mount a 350z or BA/BF falcon dbw pedal onto skyline chassis stock position https://rbfactory.shop/products/ls1-drive-by-wire-pedal-mount-to-nissan-silvia-skyline

3-  or buy a ready built one like this https://www.iee.nz/product-page/gtr-electronic-pedal-conversion?currency=AUD

 

ive found the adaptor for supras to mount on the bosch dbw pedal, but i cant find one for r34 skylines

33 minutes ago, IM-32-FK said:

so as far as im aware you can either

1- buy a bosch dbw pedal and mount it onto the chassis https://www.bosch-motorsport-shop.com.au/accelerator-pedal-module

2- Buy an adapter plate that lets you mount a 350z or BA/BF falcon dbw pedal onto skyline chassis stock position https://rbfactory.shop/products/ls1-drive-by-wire-pedal-mount-to-nissan-silvia-skyline

3-  or buy a ready built one like this https://www.iee.nz/product-page/gtr-electronic-pedal-conversion?currency=AUD

 

ive found the adaptor for supras to mount on the bosch dbw pedal, but i cant find one for r34 skylines

I went with the Outsider Garage adaptor with 350z/350gt pedal. My recommendation would be the iee unit. 

17 minutes ago, R3N3 said:

I went with the Outsider Garage adaptor with 350z/350gt pedal. My recommendation would be the iee unit. 

this one? it says for r34 gtr but i got gtt. would it fit? also im guessing that doesnt come with pedal and you need to install your oem one in it? so this product just lines up and bolts directly onto the oem position

https://www.iee.nz/product-page/gtr-electronic-pedal-conversion?currency=AUD

Edited by IM-32-FK
30 minutes ago, IM-32-FK said:

this one? it says for r34 gtr but i got gtt. would it fit? also im guessing that doesnt come with pedal and you need to install your oem one in it? so this product just lines up and bolts directly onto the oem position

https://www.iee.nz/product-page/gtr-electronic-pedal-conversion?currency=AUD

Correct. All you need is the pedal pad.

I can’t confirm if the accelerator pedal fits the GTT, but I assume it would. A quick google search shows that the pedal pad should at least fit..

send Stefan (owner of iee) a message, he’s really good to deal with and may have been asked before.

Edited by R3N3
2 minutes ago, R3N3 said:

Correct. All you need is the pedal pad.

I can’t confirm if the accelerator pedal fits the GTT, but I assume it would. A quick google search shows that the pedal pad should at least fit..

send Stefan (owner of iee) a message, he’s really good to deal with and may have been asked before.

its alright i already got the gtr metal pedal to fit gtt rod, just had to bore out the little plastic thing that sits inside the rod and the pedal

theres also this one

https://www.powertune.com.au/collections/rb26-solutions/products/dbw-electronic-dbw-pedal-suits-r32-r33-r34-gtr

 

1 minute ago, IM-32-FK said:

its alright i already got the gtr metal pedal to fit gtt rod, just had to bore out the little plastic thing that sits inside the rod and the pedal

theres also this one

https://www.powertune.com.au/collections/rb26-solutions/products/dbw-electronic-dbw-pedal-suits-r32-r33-r34-gtr

 

To be fair. It doesn’t matter which pedal you go with, as long as it bolts up. The software manages the rest.

just check the compatibility of a GTR pedal into a GTT and you’re away 

23 minutes ago, R3N3 said:

To be fair. It doesn’t matter which pedal you go with, as long as it bolts up. The software manages the rest.

just check the compatibility of a GTR pedal into a GTT and you’re away 

im not going to do it but im just curious, do you have an idea about the wiring? where do wires from pedal go, where do wires from tb go and where does the link g4ret fit in? i think i may need a second expansion loom.  this setup is costing me $2400

Edited by IM-32-FK
2 minutes ago, IM-32-FK said:

im not going to do it but im just curious, do you have an idea about the wiring? where do wires from throttle go, where do wires from tb go and where does the link g4ret fit in? i think i may need a second expansion loom.  this setup is costing me $2400

Wiring is pretty simple. The pedal and the throttle wire directly to the ecu. Remember you’re removing the aac and tps, so should free up some I/O at the ECU At the same time.

the pedal is essentially 2x tps sensors. It has 2x 5v, 2x signal ground and 2x signal wires. The 5v and signal ground can be common. So 4 wires total.

the throttle is essentially the same but with 12v stepper motor wires.

also remember that there is some re-routing of coolant hoses under the plenum when doing DBW. Check my build thread for info if you need.

23 minutes ago, R3N3 said:

Wiring is pretty simple. The pedal and the throttle wire directly to the ecu. Remember you’re removing the aac and tps, so should free up some I/O at the ECU At the same time.

the pedal is essentially 2x tps sensors. It has 2x 5v, 2x signal ground and 2x signal wires. The 5v and signal ground can be common. So 4 wires total.

the throttle is essentially the same but with 12v stepper motor wires.

also remember that there is some re-routing of coolant hoses under the plenum when doing DBW. Check my build thread for info if you need.

So I’m guessing my plug in g4+ requires a link e throttle module?

 

https://www.platinumracingproducts.com/products/link-ecu-e-throttle-g4-g4ret?currency=AUD&variant=44179266109672&utm_term=&utm_campaign=&utm_source=adwords&utm_medium=ppc&hsa_acc=9668545500&hsa_cam=18866448471&hsa_grp=&hsa_ad=&hsa_src=x&hsa_tgt=&hsa_kw=&hsa_mt=&hsa_net=adwords&hsa_ver=3&gclid=EAIaIQobChMI86K2nfmq_gIVqJlmAh37NAakEAQYASABEgLZLPD_BwE

10 hours ago, R3N3 said:

It appears so... I run Haltech, so I’m not familiar with link ecu.

Is it still okay to use the collector intake gasket, the one that sits between top and bottom half stock intake manifold? Like it was a new gasket that was put on and bolted down but the engine was never ran with it on.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah, the latter. No diff should have a centre replaced without checking clearances because its unlikely to be the same as whatever came out. Not that that stops most people just checking a new centre in
    • Major thread necro but how bad of a job is it to DIY? Looking at it online it looks like if you reuse your ring and pinion as long as those are in good condition it should be fine to just pull the axles/front cover and replace the diff that way? Or should I be replacing everything and doing preload measurements/gear mesh testing like the factory service manual mentions for the rear diff?
    • in my list I had the R33 GTR as the best Skyline. Infact I had all GTR's (33>34=32), the NSX, the GTO, the 300ZX, the 180SX, the S15 better than the FD RX7. I had the MR2 and the A80 as 'just' better. I also think the DC5R Integra looks better but this is an 01 onwards car. I also think the FC>FD. It's almost like aesthetics are individual! The elements @GTSBoy likes about the FD and dislikes about the 180 are inverse in my eyes. I hate the rear end of the FD and it's weird tail lights that are bulbous and remind me of early hyundai excels. They are not striking, nor iconic, nor retro cool. The GTO has supercar proportions. I maintain these look much better in person (like the NSX) especially with nice wheels and suspension which is mandatory for all cars pretty much. Some (or all) of these you have to see in person to appreciate. You can't write a car off until you see one in the flesh IMO. Like most people we probably just like/dislike cars which represent certain eras of design or design styles in general. I also think the 60's Jag E type looks HORRIBLE, literally disgusting, and the 2000GT is nothing to write home about. FWIW I don't think the Dodge Viper Gen1's have aged very well either. You can probably see where I rate bubbly coupes like the FD. I know we're straying now but the C4 and C5 absolutely murder the Viper in the looks department as time goes on, for my eyes. Wouldn't surprise me if people who love the FD, also love the MX5, Dodge Viper, Jag E Type, etc etc.
    • I used to hate R31s, and any of the other Nissans that led up to it, and any of the Toyotas with similar styling, because of the boxiness. They were, and remain, childish, simplistic, and generally awful. I appreciate R31s a lot more now, but only the JDM 2 door. The ADM 4 door (and any other 4 door, even if they are unique compared to our local one) can eat a bowl of dicks. The Aussie R31 is also forever tarnished by their association with stereotypical bong clutching Aussie R31 owners of the 90s and early 2000s. I think the Nissans of the 70s (other than 120Y/180B/200B) are far superior looking to the 80s cars. The 240K era Skylines are boss. The same is broadly true of Toyotas. Hondas don't ever register in my thinking, from any era. Mitsus are all horrid shitboxen in any era, and so also don't register. Subarus are always awful, ditto. Daihatsus and Suzukis also don't generally register. They are all invisible. I think the SW20 MR2 looks fiddly. The 3000GT/GTO is like that but way worse. Too many silly plastic barnacles and fiddly gimmicks ruined what could have been a really nice base shape. Kinda-sorta looks like a big heavy ST165 Celica coupe (and I'm not sure if that's a good thing or a bad thing). I think the 180SX is dreadfully bland. It's not bad looking. But it has no excitement to it at all. It's just a liftback coupe thing with no interest in its lines, and bad graphical elements (ie wide expanses of taillight plastic on the rear garnish). The S13 Silvia is a little better - getting closer to R32 shapes. But still....bland. S14? Nope. Don't love it. S15...a little better. Probably a lot better, actually. Benefits from not being like a shrunk in the wash R34 (where the S13 was a shrunk in the wash R32 and the S14 looked like a Pulsar or something else from the stable on Nissan mid 90s horrors). The Z32 was hot as f**k when it came out but hasn't aged as well as the A80. Keep in mind that I think the R33 is the most disgusting looking thing - and out of all the previous cars mentioned is objectively closest to my precious R32. It's just....real bad, almost everywhere you look. And that is down to the majority of what was designed in the 90s being shit. All Nissans from that era look like shit. Most other brands ditto. In that context, the FD absolutely stands out as being by far the best looking car, for reasons already discussed. Going behind the aesthetics, the suspension alone makes it better than almost any other car.  
    • If they just called it the "Mazda Tiffany", it would have been spot on.
×
×
  • Create New...