Jump to content
SAU Community

Recommended Posts

Mine stopped working about 6 months ago, I took it out, took it apart and found a bad solder joint.  I re-soldered that and a few other higher stress joints and put it back it, it has been working fine since.

Can't guarantee yours has the same fault though.

  • Like 1

:)  that is the fun part.. you can unplug the lamp from underneath the parcel shelf (access from the boot).  However, you need to remove the rear seat, so you can remove the parcel shelf, the lamp is attached to the bottom of the parcel shelf.

Maybe try having someone hold their foot on the brake pedal and ensure the normal side brake lights are on, then, push and flex the cable to the lamp (from the boot side) and see if the light turns on and off.  If it does, a bad solder joint is probably the issue and you will need to remove it to repair it.

2 hours ago, doggido said:

Checked out the above website and it looks promising so I will give it a go over the weekend.

So then, it leaves me one question, where does the red come from?

I dont have a direct answer, however, many years ago when I first got my 350GT Coupe, I replaced the front orange indicators with clear lenses. It failed the pink slip, but my mechanics didn't skip a beat, and put in orange caps inside the clear lensed indicators, and passed it without question. I guess what I am saying is, just try asking your regular mechanic. My guys didn't even check with me before doing it, they just told me when I went to pick it up.

If you want a selfie, maybe go to wreckers and find a broken red plastic taillight, and cut it to fit & cover the globes; or even a smaller upper taillight from a different car. Maybe even heat it a little to conform to a shape. Just spit-balling

Yeah, well, what's worse is that the DIY link above used RGB LEDs driven to make white. They could have made red. Maybe not as bright, but then winding up the brightness by going white and then filtering down to red with the red plastic diffuser is probably going to have the same effect.

 

As I was doing the rounds of the local wreckers, I found one that had a V35 in the yard which they haven't stripped yet. I grabbed the brake light out of it and got them to test which all LEDs worked. I ended up getting it for $60NZD. As long as I can at least a couple of years out of it I'll be happy.

  • Like 3

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
    • Thanks Paul I reached out to Autotainment but they no longer work on JDM cars as the guy who used to do the work moved on and is no longer doing that kind of work. I am talking with Level Up Audio though.
×
×
  • Create New...