Jump to content
SAU Community

Recommended Posts

Hey all,

 

Is an ethanol content sensor required for an E85 only tune?

I was under the impression it was due to the variable nature of pump E85- which can vary wildy in ethanol content.

I guess my question is- can a tuner compensate for this with a flex fuel sensor or is it not required for straight E85?
 

I just bought one but i'm unsure if I should just return it.

Cheers all!

It's not strictly necessary, because, whilst the wildly "variable nature of pump E85" is a thing, it doesn't really vary so much that it has to be a problem. It can often be as low as 70, from what I understand, and even somewhat higher than 85. But here's the thing. The knock resistance from ethanol content pretty much reaches a maximum somewhere around 45% ethanol content. Thereafter the extra ethanol doesn't really provide much more ability to put in timing, safety from knock, etc. What it does do though is affect the required stoichiometry. For lower E content, you get richer (for a fuel system/table that assumes E85). So you get safer. And slower. Above 85%, unless the tune is pretty close to the edge of being too lean, you should still be fine. So if you want to keep your tune nicely optimised against varying E content, then....you need a sensor.

If it were me, I'd put a sensor in. The downside here is that you must do the full flex tune to get the benefit from it. You have to have a base map on one fuel and another on the opposite extreme of the E content to interpolate against. I wouldn't think that tuning on exactly E85 (or whatever happened to be coming out of the pump that day) would give the ECU anywhere to adjust to based on what the ethanol sensor is saying, unless there's that other fuel's tune in there also.

  • Like 1

I think it depends on whether you are using pump or can e85, the stuff direct from the refinery is pretty strict e85 I understand while the pump stuff varies from season to season to give you a chance starting the car on a cold morning.

I'd 100% put it in if I was even considering some ethanol.

  • Thanks 1

Personally even if I planned on running straight E85 all the time with no variability to account for cold start I would run a flex fuel sensor purely because any time you switch between pump gas and E85 you'd have to either fully drain the tank. I want to be able to switch to pump gas halfway, end up with E30 or whatever it ends up being and just keep driving without having to deal with AFR trims being all over the place.

If you were 100% sure that you will never ever run anything other then pump e85, then sure you could get away without running a flex sensor. 

Lets say the car was tuned on a tank of e80 and everything was setup perfectly on that %blend, as you drove the car and the ethanol content varied from e70 to e85 depending on what the fuel bowser was filled with at the time, you would not notice any change in how the car behaves. It would make the same power and drive exactly the same regardless of if it was currently at e70 or e85 or anything in-between. 

The only way you would notice anything is if you had a dash/gauge telling you that something was different, e.g. AFR is  currently 11.3 however when tuned it was 11.5 under the same circumstances. These small changes will be impossible to feel in the way the car actually performs.

So, should you use the flex sensor? I'd say yes, even if it was just to give you the option to use pump 98. There might be a situation in the future you haven't accounted for where you run out of e85 or it's not available for whatever reason, now at least you can still run the car happily on 98. 

Can you run without it, yes.

Should you, probably not.

My car runs 1 as it's flex tuned. I run e85 all the time, may run 98 once a year just to purge the system out.

In Victoria, the ethanol content from United pump e85 seems very consistent, my sensor reads it as 78-79%, have seen 80-81% a couple of times. I haven't verified how accurate my sensor is but wouldn't be too far off. This is over 5 years, never been under or over those figures.

On another note, you could get one of those portable ethanol test kits but you would need to take a sample each time. 

Since you already have the sensor, why not just use it. In future you may decide to run flex and it would be 1 less thing required.

  • Like 1
  • Thanks 1

Thank you all for the great replies.

The car plan is straight E85- as the engine isn't in great health with 130psi across all 6 cylinders on a factory 25DET- so low compression.

I want to prolong it while I save up for a rebuild. But I do hope for mid 400whp with E85 in the meantime.

I am thinking about not using the Flex sensor- unless the tuner will drop a bit of 98 in the tank to bring it down to say E60-70- but they'd probably not do this and just tell me to get a flex fuel tune.

I haven't put it in yet and $250 back into my bank account will certainly be beneficial to me right now.

So basically a good idea if running flex, bad/pointless if running straight E85 since it won't effect knock anyway- only stoich point- that's the summary i've got.

35 minutes ago, CLEM0 said:

Thank you all for the great replies.

The car plan is straight E85- as the engine isn't in great health with 130psi across all 6 cylinders on a factory 25DET- so low compression.

I want to prolong it while I save up for a rebuild. But I do hope for mid 400whp with E85 in the meantime.

I am thinking about not using the Flex sensor- unless the tuner will drop a bit of 98 in the tank to bring it down to say E60-70- but they'd probably not do this and just tell me to get a flex fuel tune.

I haven't put it in yet and $250 back into my bank account will certainly be beneficial to me right now.

So basically a good idea if running flex, bad/pointless if running straight E85 since it won't effect knock anyway- only stoich point- that's the summary i've got.

Why would you want to tune the car on e60-e70?

I don't think anyone said it was bad or pointless to use a flex sensor if running pump e85 100% of the time. 

I would say the summary is closer to - 

* Yes you can run the car on pump e85 without a flex sensor

* There are benefits to using a flex sensor even if you are always on pump e85. It's up to you if you think those benefits are worth the very small outlay to install the flex sensor.

 

5 minutes ago, Murray_Calavera said:

Why would you want to tune the car on e60-e70?

I don't think anyone said it was bad or pointless to use a flex sensor if running pump e85 100% of the time. 

I would say the summary is closer to - 

* Yes you can run the car on pump e85 without a flex sensor

* There are benefits to using a flex sensor even if you are always on pump e85. It's up to you if you think those benefits are worth the very small outlay to install the flex sensor.

 

Thank you- that came across better than how I summarised it.

I would not be getting the car tuned on 98, and if E45 and E85 are minimal in regard to knock resistance, then if I got a bad batch of E85 it wouldn't be detrimental to the performance or safety of the car- so essentially unless I do plan to run flex/98, the only benefit i'd get is consistent fuel trims/AFR and more consistent economy/cold starts.

Install the flex sensor.

One day you're going to rock up to United on a low tank of fuel thinking you'll fill up, then to find out their tanks are empty.

Now you have probably 5L of fuel left in your tank and wonder how you'll get home. That tow truck emergency call out fee + towing fees will cost more than your flex sensor.

 

  • Like 4

There's no real downside and it's not strictly required. Caltex used to serve E70 to E85. As Bill mentioned up above, United has been E80-85 pretty much forever. Never ever saw that change. I suppose the offensive price gouging for the product is worth something.

(then again, Ethanol lowers the price of 91... so... they're probably maximizing the 'cheap stuff' by keeping that Ethanol content up in E85)

1 hour ago, Murray_Calavera said:

Why would you want to tune the car on e60-e70?

I don't think anyone said it was bad or pointless to use a flex sensor if running pump e85 100% of the time. 

I would say the summary is closer to - 

* Yes you can run the car on pump e85 without a flex sensor

* There are benefits to using a flex sensor even if you are always on pump e85. It's up to you if you think those benefits are worth the very small outlay to install the flex sensor.

 

E30 is popular in my area to bump up octane enough to make enough power on our terrible fuel quality in California while not suffering too much of a range deficit. It also helps with not destroying HPFPs in GDI applications.

On 3/22/2023 at 2:10 PM, GTSBoy said:

Be aware that a worn set of rings will let more water-filled blowby gases into the sump. You will want to change your oil close to twice as often as would normally be expected for E85, unless you're happy for it to all go to shit down there.

Thanks.

I did a wet test and it jumped about 7-8psi. So i'd say rings aren't amazing.

How often would you suggest a change in oil?

10 hours ago, Dose Pipe Sutututu said:

When it smells like fuel and/or looks milky from E85 and/or when it's a dark colour.

I dunno about the smell, oil will smell like E85 if you do so much as drive it out of your driveway... 

11 minutes ago, Kinkstaah said:

I dunno about the smell, oil will smell like E85 if you do so much as drive it out of your driveway... 

jesus, how much enrichment do you have on cold start? lol...

 

2 minutes ago, Dose Pipe Sutututu said:

jesus, how much enrichment do you have on cold start? lol...

 

Not sure, I have no need for Expensive-Gouge-Juice anymore, though I do have the capacity.

I remember not needing to touch any of the enrichment tables for start with the ol Haltech PS2000. Would start perfectly with full ethanol in the middle of winter without any issues. Never had any cold start problems at all, or hot start for that matter, was the most overblown 'problem' E85 ever had. At least for me..

But ye, do an oil change then drive for 100km then smell the oil filler cap. It smells like E85 really fast in my experience and isn't an indicator that the oil is ready to be changed yet.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok glad you clarified on the frenchy’s options , I was worried about if my oem hoses would fit the new compressor or not if I just bought the bracket/compressor kit ,  didn’t realize they also sold a larger full conversion kit. Hmm may just go oem in that case then to make it easy only because I plan to sell this car to upgrade to a 32 GTR or 34 GTT.
    • Right, here's a video of the basic operation at least.  This is what you can expect day to day when you turn the car on and it boots from standby.  The only thing from a media point of view I haven't gotten working is for it to autoplay plexamp when it turns on from standby (it works from cold boot) but that's more of a plexamp problem as it will autoplay other music players.  Also attached is my one stray cable.  It's part of the screen's wiring adapters but there's just nowhere for it to go in my car.  I've just now done a bit of research and found a matching port on a 2010-2014 head unit with BOSE.  Mine has no BOSE so that's that case pretty much closed I think.  Plugging in the Infiniti AC panel basically did nothing for me, so that's a dead end as well.  Next port of call is to mess with this CANBUS module and see what I can find from it.  I found this resource containing the DBC files for a 2010+ G37 : https://github.com/icecube45/Dash_InfinitiG37/blob/master/InfinitiG37.dbc I'll now have something to go from when I try to extract my CANBUS data so I can see if the HVAC Mode, Fan Speed, Temperature, etc. match and also the gear shifter position.  It's a pretty big assumption that it's just mismatched CAN signals but considering all the devices in the CAN network are talking to each other (AC can be fully adjusted just with no info on screen) it might be a safe one.  I will report back WhatsApp Video 2025-02-26 at 12.49.10.mp4
    • Thanks for that Paul.  Do you think if I posted a picture you'd be able to remember where it went? 
    • Sorry Duncan, I didn't get a notification for the replies.  Thanks for responding!  It's a full Android device, but does allow you to use CarPlay/AA as well.  This is the one I bought from NaviRS on AliExpress: https://www.aliexpress.com/item/1005006368602668.html?spm=a2g0o.order_list.order_list_main.111.59aa1802JDzQ0E - the 2K 8G-256G CAM variant but it seems to have gone up by £170 since I bought it!  My purchase was £307.14.   It's not the fastest thing in the world but performs perfectly adequately.  It stays on standby unless I disconnect the battery and let it power down, then it's just a fairly standard Android bootup time from cold.  The DSP Equaliser is very nice and made the standard stereo system sound pretty decent compared to the stock screen.  Perhaps I can take a video of it when I get a sec. It *allegedly* supports the reverse camera, but I'm yet to get that working.  It has options for reverse cam (a camera unit can be bought separately) or 360 cameras (also bought separately).  To be fair it doesn't seem to detect that the shifter was put into reverse but I'm working on a theory about this as well.  At the moment I'm going without which is a bit annoying considering the car is an absolute canal barge but so far I haven't caused any damage I'll grab a picture of the wire I'm missing later today when I can get outside.  My theory, by the by, is that not only is the head unit different, but the CANBUS network has different signals for the different years.  I think this because I have a spare AC panel from a newer Infiniti G37 (as opposed to my Nissan panel) which wouldn't control anything except the volume when I had it wired up with the stock system.  I'm going to throw it back in and see if the screen will respond to it.  I've just ordered an arduino CANBUS module so I can have a look at the signals going around the car and see if I can spot anything.  I'm thinking if I can work out what it's expecting vs what it's getting I might be able to translate and relay the signal back but so far just a theory anyway. I also found this on my travels, so far the only one that specifically matches my car: https://www.aliexpress.com/item/1005002822934280.html?spm=a2g0s.imconversation.0.0.33433e5fgttovi If you look at the picture of the before, it has the card reader slot, and the picture of the head unit is exactly the same as the one pictured in my original post.  I asked if they sell the cables separately but sadly they won't.  I didn't want to just buy this one because it's a super old Android version and only dual core - likely slow as hell. 
    • As above, you did refill the coolant and burp the system before running it again didn't you?
×
×
  • Create New...