Jump to content
SAU Community

Recommended Posts

1 hour ago, ACTIVE-LSD said:

Nice looking good mate. how many hours did that take you? If you're fastidious with the colour difference, you can take off the bonnet hinge and get it paint matched in rattle cans by a paint shop. use matte clear coat as engine bay is not gloss from factory.

All up, probably 8 hours for both sides.

Fully removed any trace of visible spot rust, rust converter just in case and then redid it all with rust primer and top coat.

Bit of a mission, rust wasn't awful but this should be a solid band-aid.

Few spots I couldn't get to without a lot more work- but thankfully looks very early stages of rust, so i'll address them at a later stage.

  • Like 2
2 hours ago, BigDogRB said:

Few spots I couldn't get to without a lot more work- but thankfully looks very early stages of rust, so i'll address them at a later stage.

If you are thinking of going all-in, have a look at @Shoota_77's build thread. He was taking it all the way a while ago with his engine bay and wheel arches and was documenting it all. It looks like a serious rabbit hole though. You two could start a mental health support group after going through it ;)

Here's a rough starting point:

There's a bit more on the pages before. And after of course.

On 4/8/2023 at 4:34 PM, ACTIVE-LSD said:

 

Nah top plate is different as others have mentioned. not sure about the sides though. Are you sure SR Auto bodies are shut down? their website is still active.

 

Yeah I also spotted that. As far as I know the shop for full restorations has shut down - check their IG page. Whether this applies to the online store I am unsure. They do have the strut tops for sale online which is worth a shot. I've been tempted just to buy them for spare, at <£300 the price isnt bad.

On 28/03/2023 at 10:51 AM, Dose Pipe Sutututu said:

You will need to cut into it, rust converter and weld up, add seam sealer, etc. then respray.

Not impossible, but not fun either lol.

I went in for a basic "respray", nek minnit.............. yeah could have just bought another car with that money LOL.

I had the same issues.

Mood

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The cam I am actually putting in (a few posts up) is actually smaller than my current one. At least duration/overlap wise. All the chop stuff I hear just sounds like an engine running badly, because it is. I then envision driving it around in 1st gear and being massively sad about it bucking to the beat of said chop. There is an idle video of someone with a similar cam floating around the internet, but mine is a custom cam (so is his) so it'll never be the same, plus the fact exhausts are entirely different. What I want to do is put some bullet mufflers/race mufflers in to replace a couple sections straight pipes that currently replace the two extra cats that I don't need. But this is even further down the line!
    • I can tell you now, when the bracket that the little hydraulic ram attaches to snaps, with a subframe, and V8 from an AMG C63 on it, it sounds like someone letting shotgun off right beside you. It leaves your ears ringing, and a huge thankfulness that you never ever put a body part under something heavy that's only supported by a hydraulic lift...
    • Still not a guarantee fix. I used a high quality butyl-mastiq (the black goo that's not really silicone nor polyurethane, same stuff they use from the factory that just spreads out like melty cheese), and I still get lots of water on both sides of the trunk when raining or washing the car. I also suspect the factory spoiler rubber gasket might not be sealing well, so I'm thinking of adding a thin layer of grey silicone around the bolt holes on both sides and see if that's where it also leaks from. The biggest issue is that these cars don't come with a drain hole on each side like other coupes and hatchbacks.
    • I hate it, but maybe he could paint it Monster jam style and call it...godzilla?
    • Would seem to me to be appropriate to go GTR style bar. There are options with and without N1 vent holes, with the GTR lower lip integral (because FG copy). https://justjap.com/search?q=r32 bumper  
×
×
  • Create New...