Jump to content
SAU Community

Pedestrian pop up hood system replacement after accident

Youuii
 Share

Recommended Posts

Youuii Newbie

Youuii

Posted
Posted

Hey everyone, 

I've read quite a few articles and forums about this if not all of them, however I couldn't find anything that could help me. for a bit of context, I've had an accident and my pedestrian hood pop up system activated. I have replaced the actuators with resistors and replaced the module itself with a second hand one. However I still have the light on the dash, I've tried the pedal dance and tried clearing fault codes with a cheap scanned but nothing has worked. the light on the dash is solid unlike other instances when it flashes.

so my question is, what do I need to do now that I've replaced the actuators and the module, would the crash sensors store crash data and need replacement too? or do I need to find someone with a consult tool to reset the system? I don't think I can go to a dealer because I've replaced the actuators with resistors. 

I believe @The Max solved it by resetting the module's EEPROM, but I don't have any access to the equipment needed and don't really know anyone in Sydney that does that kind of service, anyone has an idea if someone like that exists?

sonicii Veteran

sonicii

Posted
Posted (edited)

Does the different module need to be paired with the BCM for it to talk?  Are you sure the resistors are the correct value to imitate the bonnet actuators?  The impact may have damaged one of the sensors behind the bumper too.

I doubt any sensor would have the ability to store data, you may need someone who can read the codes to determine what is triggering the light.

The pedal dance is really difficult to do with the push button start as it takes a second or so for the button to actually turn the ignition on/off, so you have to compensate for that when pressing the button after 'x' seconds.

Nissan Datascan III might work, it can read a lot of the components in the Q50 (but not all).

Edited by sonicii
Youuii Newbie

Youuii

Posted
  • Author
Posted

I'm not sure if it needs to be paired with the BCM or not tbh, there's really no information online or a service manual that tells you what to do after replacing the module. I believe the resistors are correct, I bought them of ebay where the specific part number and system was mentioned and they came ready with the correct connector and everything. 

With the pedal dance, I'm not sure if that can even solve my problem as it requires the light to flash, mine doesn't do that, it just stays solid the whole time. 

I might look into getting that Nissan Datascan III software, see if it helps. Thanks mate. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      Tyres you use(d) and how u would rate them

      By The Bogan · Posted

      Done about 5k Km on the PS5's now, excellent street tyres, great in the dry, and the wet, seem to be wearing very well, I haven't measured tread depth, but it looks like minimal wear, I also had a different alignment done about 1500km ago,  From looking at the tread wear, which is really only minimal, the alignment changes were based off how the tread looked, and how it felt throwing it around, the changes have shown great results 215/45 17 at 32 psi Front Caster: 5.5° Camber: -1.5° Toe: 0.0mm Rear Camber: -1.0° Total Toe-in: 1.5mm I actually prefer PS5's now over the RS4's, as the PS5's are much better in the wet IMO, and as the MX5 gets driven in all weather conditions doing daily duties, hwy trips, and blasts in the mountains, wet weather grip is high on my priority list
    • Russell2208
      Attesa ETS Pro Install on R33 GTR

      By Russell2208 · Posted

      To update this thread. I got sent a replacement Attesa pro unit and all is now working as expected. Cheers
    • Ozdavroz
      The FD RX7 is the best looking 90's JDM car

      By Ozdavroz · Posted

      FD is so sexy she can pull off tri-spokes
    • Butters
      Front LSD Quaife , how streetable ?- QDF3L Owners

      By Butters · Posted

      Indeed they do. Best my diff builder could tell is it's a combination of the different cut/angle and it would seem they lap them in well on accell but less so on decel. He had to use a slightly different pattern to the lap to get the best result noise wise. Also as the rear diff runs in, the whine is getting less.        Overall they seem like a good thing so far. He's done a few neat crown/pinion before but all for race cars with loud everything, in most cases the exhaust is louder, so I am the first to notice.... and be somewhat of a pain   
    • GTSBoy
      R34 4 door indicator and horn issue

      By GTSBoy · Posted

      What do you mean by "test"? It sounds like you're just switching things on and off that you already know don't work. Get the wiring diagram and a multimeter and start looking for power where there is supposed to be power and earth where there is supposed to be earth. Look for continuity across switches that are otherwise unresponsive, etc etc.
×
×
  • Create New...