Jump to content
SAU Community

R32 GTST differential bearings

penny627
 Share

Recommended Posts

penny627 Newbie

penny627

Posted
Posted (edited)

So the pinion gear bearing (driveshaft side) went out and I'm trying to find a replacement. Are all r200 differential bearings the same? I've found a complete kit for a 350z, 370z, etc as well as 300zx, 280zx. Will either of these work?

Screenshot_20231109_090003_Chrome.jpg

Screenshot_20231109_090302_Chrome.jpg

Screenshot_20231109_085917_Chrome.jpg

Edited by penny627
Link to comment
https://www.sau.com.au/forums/topic/485070-r32-gtst-differential-bearings/
Share on other sites
GTSBoy Grand Master

GTSBoy

Posted
Posted
10 hours ago, penny627 said:

Are all r200 differential bearings the same?

No.

The 350/370 era stuff is likely to be different. Might be compatible, but I don't know, and Nissan was in a state of flux at the time. The Z32 would likely be same same, for an R200 (not the R230) as it was exact same period. Earlier 280ZX etc could well be different, as they were long nose diffs (I think).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Need AC Compressor for R32

      By GTSBoy · Posted

      The Frenchy's kit is the way to go forward. A modern compressor that weighs about 1/2 as much, is at least twice as efficient, and will do a good job on R134a. And of course the kit has everything else you need to connect it up and have it work properly.
    • Zabuza
      Need AC Compressor for R32

      By Zabuza · Posted

      Hey all , I am in the process of having the AC system in my r32 GTST converted from r12 to r134a and I’m being told my compressor has gone bad and I will need a new one. I was wondering if anybody has any suggestions for what is the best route to go aside from dropping $1500 on a new oem one? I did see that Frenchy’s performance garage offers a kit to mount a Toyota compressor, has anybody actually used this kit on their car? Or is there anywhere I could purchase just a clutch? Any help is appreciated.
    • GTSBoy
      Help Understand GTT Boost Setup

      By GTSBoy · Posted

      Well, your RB20 ECU loom won't have wires for the boost solenoid, that boost sensor, and possibly one or two other things. There could be differences in seemingly random things like the charcoal canister purge solenoid, because the 25DET has to handle boost in the vacuum system and the 20DE does not. I don't know - I haven't looked. It is very likely that all the most important things are same-same, being the main sensors like AFM, CAS, etc, and the injectors and ignition. Not that you'll need the AFM for the Haltech anyway. I would suggest that you would seriously want to sit down with the pinouts for both ECUs and just go through them and highlight green what is the same, orange what is different/missing, and make a plan from there. It's not going to be difficult. It will either be the same or need to be fixed.
    • Sxnjeet
      Help Understand GTT Boost Setup

      By Sxnjeet · Posted

      yeaaa that's why I haven't done any wiring to the stock ecu harness because I have the haltech, but then that leads me to the other question of "is the pnp harness really plug and play?" or would I have to still switch some pins/wires over because the pnp is for the rb25det neo harness, and not for the rb20de neo harness. was really hoping to find something to spoon feed me since so many people have done rb20neo + t conversions, but man this is rough.
    • Dose Pipe Sutututu
      Daymo's Back! - R32 RB25DET NEO

      By Dose Pipe Sutututu · Posted

      Temu raptor, lol. At least the owner isn't your typical ranger danger lot
×
×
  • Create New...