Jump to content
SAU Community

AEM Tru Boost Install Help AND Settings for R33 GTST?

jacobzking
 Share

Recommended Posts

jacobzking Contributor

jacobzking

Posted
Posted

Can I get yalls input on the AEM Tru Boost settings for my mostly stock GTST (rb25det)?  I'd like to run maybe 7psi on low and 10psi on high.  What settings do I need to configure the Tru Boost to get these results?  

I was reading the manual and it gives me a headache talking about pulse wave and blah blah blah lol. 

Also, any tips for install would be appreciated.  I'm just gonna install in my ashtray.  

Thanks guys!

soviet_merlin Experienced

soviet_merlin

Posted
Posted
16 hours ago, GTSBoy said:

You'll possibly be the first and only person with one in an R33. Most of Australia doesn't touch AEM stuff.

Could you elaborate? I don't remember it being mentioned much in the forums.

GTSBoy Grand Master

GTSBoy

Posted
Posted

I'm old enough to remember when AEM's stuff was absolute shite. They have simply never had much market penetration into Australia, hence my statement.

I have no idea how good/bad they are right now, but there are several other brands for simply everything they do that I would choose before I even bothered to remember that AEM exist.

  • Thanks 1
TurboTapin Proficient

TurboTapin

Posted
Posted
1 hour ago, GTSBoy said:

I'm old enough to remember when AEM's stuff was absolute shite. They have simply never had much market penetration into Australia, hence my statement.

I have no idea how good/bad they are right now, but there are several other brands for simply everything they do that I would choose before I even bothered to remember that AEM exist.

AEM products are fantastic in my opinion and I have pushed to use them the last 20 years. Their fuel pumps are renowned for being indestructible (I run 2x), their ecu's have a lot more features then Haltech (Scripting, Proper IO testing, etc.) I've had zero issues with any of their products including Tru boost, widebands, WMI kits, etc. 

I wasn't ever aware of them being known for bad products, but if they did; it's changed. 

  • Thanks 1
TurboTapin Proficient

TurboTapin

Posted
Posted
7 hours ago, jacobzking said:

ugh.  that bad?

I ran one years ago in a 93 STI. They work great. Just slowly increase duty cycle until it reaches the pressure you're trying to achieve. Nobody will be able to tell you the exact duty cycle % you need for your setup for a specific boost. It will be trial and error. 

joshuaho96 Veteran

joshuaho96

Posted
Posted
13 minutes ago, TurboTapin said:

AEM products are fantastic in my opinion and I have pushed to use them the last 20 years. Their fuel pumps are renowned for being indestructible (I run 2x), their ecu's have a lot more features then Haltech (Scripting, Proper IO testing, etc.) I've had zero issues with any of their products including Tru boost, widebands, WMI kits, etc. 

I wasn't ever aware of them being known for bad products, but if they did; it's changed. 

I don’t think they’re known for junk but they aren’t particularly standouts as far as I know. 

Murray_Calavera Mentor

Murray_Calavera

Posted
Posted
On 11/22/2023 at 9:47 AM, Dose Pipe Sutututu said:

AEM widebands are decent, better than the Innovate junk - no self combusting heater circuits.

That's my experience too. Before I had a CAN based wideband, I always used an AEM wideband (I wouldn't be surprised if I was using one for over 10 years without issue). 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      Shifting questions

      By dbm7 · Posted

      Those 2 solenoids in that assembly I mention, are the PWM solenoids for torque converter lock-up clutch & EPC (line pressure control) ~ when most folks hear of 'solenoid failure', the tendency is to think electrical failure...but fact of the matter is, especially wrt the EPC solenoid (which is moving/running all the time), you can have an electrically 'good' solenoid, that's absolutely broken/worn out mechanically inside...ie; valve plunger return spring rubbing against spring retainer plate, lowering preload pressure.. ...and the solenoid armature extension limit spring wafer with bad wear/broken off petals... ...and if there's ever been any metal flying about, damage to the valve plunger end itself... ...the stuff one never really sees, unless you go the whole 10yards trying to answer the question "why is my line pressure screwy, but TCU isn't flagging any EPC solenoid fault?"...and carefully dissect the solenoid. Worst (and most probable) scenario is when the plate spring petals break off, they get held by the magnetic flux, get mashed up by the armature into little bits, which end up in the space between the armature & shading core bore, and things get stuck or randomly jam up, and your line pressure goes flat and doesn't change...and the TCU never sees it, as it doesn't actively monitor LP... ..then it gets into insidious land, if you end up with lower than expected line pressure...lets say high clutch..and the lower pressure causes it to slip ~ when I say 'slip', think say 2000rpm on the drive plates, and 1800rpm on the driven plates, because the slip is making them under-rotate by 200rpm ; you get all the usual nasties like heat and band/clutch wear, but even if it's only 20rpm slip the same thing happens...and... you'll hardly ever pick this up driving the thing with the torque converter active as it effectively masks these sorts of slippages that are line pressure related ...(the newer TCUs can detect clutch slip rate)...just  FYI as it were...  
    • GTSBoy
      MAJOR FUEL ISSUES 25det neo r32

      By GTSBoy · Posted

      There's nothing that some paddle pop sticks and extra cable ties can't fix.
    • QB6SAGR
      RB20 in need of modest love injection

      By QB6SAGR · Posted

      Hey guys, so Golebys has good prices on Bosch injectors, and also sell an adaptor to go from 1/2 length injector to standard with the Nissan 10.5mm top seal.  Does anyone know if that adaptor is to suit the 14mm or 11mm injector tops?  And re. The bottom seal, to suit my standard RB20 intake, would I be right in saying I can just slip the 14mm square section O ring over the bottom of the new injector and done? Thanks in advance guy, Cheers, Rowdy
    • kevboost7
      Magnetic Drain Plug Snapped in Half

      By kevboost7 · Posted

      F my life. I was changing the oil on my R32 GTR today as usual and ran into a bit of a snag. I drained the oil out and was getting ready to finish the job by tightening the drain plug, however The stupid magnetic oil drain plug snapped in half, right at the magnet part. After about an hour of trying to remove it, I used a drill bit, which unfortunately pushed the magnet all the way into the pan, and just leaving the hollow threaded part of the bolt remaining. I was able to remove the hollow portion of the bolt from the oil pan with some pliers but the magnet is still in there.  So, the question is, should I drop the oil pan to get the magnet piece out, or is it okay to leave it in there? I really dont want to drop the pan, i'm about to go nuts.  PSA: Do NOT buy a BLOX magnetic drain plug. This is the one i had.    https://bloxracing.com/products/magnetic-oil-drain-plug-m12x1-25mm?variant=37131252859052&country=US&currency=USD&utm_medium=product_sync&utm_source=google&utm_content=sag_organic&utm_campaign=sag_organic&gad_source=1&gclid=CjwKCAjw47i_BhBTEiwAaJfPpgti1D2JwO7TDuMpXuqeQPCuIQSAfwxpWQH5rF9MD7sm5SCZDWLR_RoC_YoQAvD_BwE    
    • 25debt
      MAJOR FUEL ISSUES 25det neo r32

      By 25debt · Posted

      I actually have an aftermarket hanger, the detschwerks x1 hanger, but my dw420 has never really sat in it correctly, good to know I can just modify it a bit to suit. Yeah cheers man will definitely have a play with it and hope it solves my dramas.
×
×
  • Create New...