Jump to content
SAU Community

Recommended Posts

Hello everyone ,

I am looking for the height rating of the RB30, because I would like to know if mine has already been planed or not

mine placed on my marble is approximately 286 millimeters
and the shirt is 152 millimeters

 20240202_1731531.thumb.jpg.dc96187a2ac675b14bb874986f823c01.jpg    20240202_1727091.thumb.jpg.e24547ade9ded71044a5a3644c5a565a.jpg

Your measurement technique will never tell you the deck height. Tape measures are not accurate enough, and you need to measure from the centreline of the crank, not the bottom of the skirt.

I don't know what the correct dimension is. Hopefully someone will chime in with it. But in the mean time, buy yourself a good quality 1000mm ruler and a straight edge. The straight edge is to take the place of the crank. You need to bolt on the main caps, and measure from the top of the main bearings to the deck, and from the bottom of the bearings to the deck, and average those two numbers.

thank you GTSBoy,

I'm going to do as you told me with my rigid rules. afterward I did as it was just to see if my block is still valid or not, otherwise it won't be much use to me to work on it

It would only be better with your method thank you once again, I hope there will be people who will respond too I will see

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
    • Thanks Paul I reached out to Autotainment but they no longer work on JDM cars as the guy who used to do the work moved on and is no longer doing that kind of work. I am talking with Level Up Audio though.
×
×
  • Create New...