Jump to content
SAU Community

How do i get more power out of my ENR34

ENRR34

By ENRR34,
in Engines & Forced Induction

 Share

Recommended Posts

Duncan Grand Master

Duncan

Posted
Posted

Basically, you don't.

Of course it is possible to get 10% more out of an NA car, but it is an expensive path. From there for sure you can get 50% if you go nuts with cams, headwork, capacity for....very expensive.

Or you put a turbo on it an run 50% more for the same ballpark cost as the 10% more NA mods.

  • Like 1
Murray_Calavera Mentor

Murray_Calavera

Posted
Posted

If your a young fella on your P's, I'd say the sensible option is to upgrade other areas of the car, tyres, suspension, brakes etc.... And if your interested, start doing track days and improving as a driver. 

Once off your P's, its engine swap time (or turbo time, gearbox upgrade time, etc). 

Probably not what you wanted to hear though, sorry. 

Umm but to answer your question, your only option that makes sense is to add spray. Not a very sensible option, one of those if you have to ask, its probably not for you. 

  • Like 1
Murray_Calavera Mentor

Murray_Calavera

Posted
Posted
17 minutes ago, ENRR34 said:

If I was to try fit a turbo kit on it would it be worth it, could the NA engine block be able to handle it and is it an affordable ish option?

 

I wouldn't be worried about the engine, I'd be concerned for your gearbox. 

  • Like 1
DanGreen006 Rookie

DanGreen006

Posted
Posted (edited)


No turbo? 

well

Stroker crank, pistons rods, head work, high comp, valve spring retainer cams, os88 run it on nitro methane, get roll bar, get it teched run a chute and skinnies on the front wheels, obligatory green neon under the car

You'll still get chopped by a toothless crackhead with a catless stg1 barra xr6 at the lights but at least you never put a turbo on it

In all seriousness as someone above mentioned, barrage it with a ZF8hp when funds allow, it will be more fun and cheaper in the long run

Edited by DanGreen006
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • weikleenget
      R32 GTR clutch master cylinder adapters

      By weikleenget · Posted

      Hi again all, I’ve tried doing some searching on the topic but couldn’t find the answer I’m looking for.   I deleted my clutch booster because it had an air leak and was squealing like a hog, and now my clutch has very poor pedal feel and the friction zone is way too small, so I believe I need a bigger diameter clutch master cylinder to compensate for not using the booster. I found a Wilwood option that’s 3/4” for a good price and will fit my 3AN clutch line, but all the firewall adapters I see online such as RB factory or Chase Bays are listed as RWD only (GTST/GTS). Link below. https://rbfactory.shop/products/nissan-to-wilwood-girling-clutch-master-cylinder-adapter My question is if these adapters will also fit a GTR, and if anyone has experience using a 3/4” CMC without the booster, my clutch is a Nismo coppermix twin plate.   Thanks, always appreciate the advice!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Catching up on a post, I've replaced the external shark fin with a small 4g antenna (no further drilling, just a 1mm embiggening of the existing hole, and run that to where the dual battery models have the battery in the left rear guard.  No idea what the factory antenna did, but removing it had no impact on anything I use, according to the US manual the GPS antenna is in the dash and it still works fine Also ended up stealing battery power from one of the amps and ACC power from a unit nearby to add an ACC relay to power it. The mounted the booster, wifi, power socket and antenna splitter in the rear left guard out of the way, all out of site with the boot trims in
    • GTSBoy
      Skyline R34 Suspension Drama

      By GTSBoy · Posted

      What drama? The only drama you're going to have is the near constant work to maintain all those sphericals. I only have sphericals in my front caster rods and front upper CAs (because both of these are near compulsory in an R32). I have had the front arms out of my car 34 times already this month, and if the new replacements arrive today, I will have them out and apart again tomorrow. Chasing clicking and clunking that comes from sphericals being a.....poor choice for a road car. Moisture and dirt are not their friends. I have been contemplating a change to my rear subframe that would require me to use sphericals in my lower CAs. And.....I don't want to have them that close to the road.
    • Kinkstaah
      Skyline R34 Suspension Drama

      By Kinkstaah · Posted

      Did you need anything else you've already done? If you had it before... and liked the changes after, then supposedly it'd be more of the same. The idea about most suspension arms is to tune geometry that the OEM arms max out at/can't handle because they weren't designed to have the car setup in such a way that 'looks good'.
    • drifter17a
      Skyline R34 Suspension Drama

      By drifter17a · Posted

      I have replaced everything on my r34 including suspension to Miester R, all rear subframe bushes to poly, all arms to metal adjustable and same in front.   only thing I haven't touched is the front lower control arm. Should I? what improvement can i expect ? I mean the one on the link below?   Car drives perfectly, it is just me thinking everything is either puly bush or hard bearing type so should also do lower control arm front but do I really need it ? https://www.japspeed.co.uk/product/suspension/adjustable-arms/nissan-200sx-s13-s14-s15-skyline-r32-r33-r34-adjustable-suspension-front-lower-control-arms/?gad_source=1&gclid=Cj0KCQiAo5u6BhDJARIsAAVoDWs5V_PauQPf0kx3zFCaA4tOC9Q7JSIsfJWma_jAPN2f1sJA686djOwaAidgEALw_wcB
×
×
  • Create New...