Jump to content
SAU Community

Recommended Posts

I just purchased a R34 GTR and drove it 2000 miles back home (once in a life time opportunity - best drive of my life) but around 500 miles in something happened with the clutch where the car would not go into first or reverse when stopped. So I currently have to start the car in 1st or reverse and then "release" the clutch like normal and the shift like normal once I am moving. And If I try to put the car in first or reverse when stopped I can feel some vibration on the shifter like something is still connected between he engine and the transmission. Nothing is wet around the master or slave cylinder and I seem to get full travel from the slave cylinder - I am thinking the hydraulics are good since I can have the car in first gear with the clutch depressed and engine running and not stall out. And when the engine is off everything shifts as it should.

 

Video of slave cylinder movement

Firstly, great to hear you are enjoying the new car!

I'm not a gearbox expert but I agree the hydraulics look OK. As you have a pull clutch it is possible the release bearing or fork are disconnected from the pressure plate, but you should be able to see/correct that through the gap in the bellhousing. If that is the problem you should be able to reconnect it through the bellhousing gap as you would when putting the gearbox back in. This is the easier problem but less likely as you would also have issues changing gears on the move unless you are rev matching (and you didn't mention you were).

Is the issue definitely only 1st and reverse? can you choose second while stationary with engine running and clutch pedal down? That would imply it is some sort of selector/linkage issue which is going to need gearbox off to fix

Disclaimer: totally different car

My Honda's shifts were a "little" notchy at high RPM and the clutches engaged pretty high, no amount of bleeding fixed it, I thought it might have been the syncros, turns out the old girls clutch, pressure plate, fork and thrust bearing were worn, after replacing those OEM parts with new OEM parts the clutch engagement was much lower, was lighter, and shifted at high RPM like butter

I'm not saying this is your issue, but there are alot of moving parts that are considered consumable items hidden in there

Well no one would have guessed - including me. I removed the clutch to find that one side of the clutch completely ripped off the plate. So I drove about 1500 miles with one side of a clutch lol. I guess the ripped off clutch material was still kind of connected causing the transmission to not stop completely thus making first gear hard to get in.

 

p.s. don't replace your clutch on the floor of your garage unless you have a great therapist  

73294921392__FA6F7CDB-E5D0-4E71-9D76-A8F7ADC04A56.jpg

IMG_2085.jpg

IMG_2169.jpg

6 hours ago, te37 said:

p.s. don't replace your clutch on the floor of your garage unless you have a great therapist  

yeah aint that the truth!

I would still double check all of the heights and fork operation, and replace the throw out bearing while it is all apart.....depending how long the car sat without use it might be an age problem (if that is even a thing with clutches!) but it could also have been slipping a little for a long time

11 hours ago, te37 said:

p.s. don't replace your clutch on the floor of your garage unless you have a great therapist  

Me and me friend did this on his 33R in his basement carpark only using the torch from our phones. That top starter bolt musta taken us about an hour alone. Needless to say I am now an expert in removing R boxes in a basement carpark with iphone torch and limited number of tools :D

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
×
×
  • Create New...