Jump to content
SAU Community

Recommended Posts

Hey all I have an 99 R34 sedan - RB25DE NEO and it’s running rich/poor but I’m not sure why. It was running poor when I bought it and the only thing the PO did before hand was drop the cat which he said caused the issue (Unsure if that’s true or not) The car has a chop while idling but once it warms up properly it runs smooth but still has the CEL. I ran the code and it gave me a MAF issue so I used sensor clean which didn’t work then replaced it with an aftermarket MAF but from a reliable seller which gave me code 55 but it still runs poor. I’ve also replaced the coil packs and checked the spark plugs and raised the O2 sensor out of the exhaust to allow it to get more air but still nothing. Any help would be great as I’ve spent a lot of time and money trying to diagnose this issue. Here’s a vid of it idling 

hope someone else has had this issue and can help fix it thanks

 

 

Link to comment
https://www.sau.com.au/forums/topic/485674-r34-running-rich-but-code-55/
Share on other sites

2 hours ago, Connorrd said:

...and raised the O2 sensor out of the exhaust to allow it to get more air ...

 

 

WTF?

What spark plugs did you use? Gap?

Have you cleaned the injectors?

Shouldn't really have caused your problem, but refit the cat.

2 hours ago, Connorrd said:

Hey all I have an 99 R34 sedan - RB25DE NEO and it’s running rich/poor but I’m not sure why. It was running poor when I bought it and the only thing the PO did before hand was drop the cat which he said caused the issue (Unsure if that’s true or not) The car has a chop while idling but once it warms up properly it runs smooth but still has the CEL. I ran the code and it gave me a MAF issue so I used sensor clean which didn’t work then replaced it with an aftermarket MAF but from a reliable seller which gave me code 55 but it still runs poor. I’ve also replaced the coil packs and checked the spark plugs and raised the O2 sensor out of the exhaust to allow it to get more air but still nothing. Any help would be great as I’ve spent a lot of time and money trying to diagnose this issue. Here’s a vid of it idling 

hope someone else has had this issue and can help fix it thanks

 

 

Code 55 doesn't matter. The ECU can only detect a total MAF failure, partial failures or bad signal response curves are not detected. Get an OEM MAF, nothing else works for these cars. Do not "raise the O2 sensor out of the exhaust", whatever the hell that means.

CEL is also the catalyst overtemperature alarm (which should be obvious by the appearance of the graphic in the light).

It is a better than even bet that the temperature sensor is f**ked from having been unceremoniously hoiked out of where it is supposed to be (ie, the missing cat).

5 hours ago, blind_elk said:

WTF?

What spark plugs did you use? Gap?

Have you cleaned the injectors?

Shouldn't really have caused your problem, but refit the cat.

I meant O2 spacers but forgot the wording lmao I have BKR5E-11 Copper set to 1.0 and I am going to be cleaning them soon just wondering if anyone else had any ideas. I’ll try out the cat thing also see if I can find one on ebay

4 hours ago, joshuaho96 said:

Code 55 doesn't matter. The ECU can only detect a total MAF failure, partial failures or bad signal response curves are not detected. Get an OEM MAF, nothing else works for these cars. Do not "raise the O2 sensor out of the exhaust", whatever the hell that means.

Meant O2 spacer forgot the word any reasonable places to find them? Or do I have to suck it up and pay the 500

21 minutes ago, Connorrd said:

Meant O2 spacer forgot the word any reasonable places to find them? Or do I have to suck it up and pay the 500

O2 spacers are not going to help you here. The engine doesn't even have a post-cat O2 sensor. There is no silver bullet to fixing cars on the cheap other than giving up your own labor and time to do it.

11 minutes ago, joshuaho96 said:

O2 spacers are not going to help you here. The engine doesn't even have a post-cat O2 sensor. There is no silver bullet to fixing cars on the cheap other than giving up your own labor and time to do it.

Interesting I’ll try replacing it and installing a factory maf and seeing how that goes

5 hours ago, Connorrd said:

Interesting I’ll try replacing it and installing a factory maf and seeing how that goes

If an OEM MAF is expensive (I have no idea what they go for) I would strongly consider putting the money towards an aftermarket ECU and putting the MAF in the bin. 

Also, how do you know the car is running rich? Do you have a wideband o2 sensor setup?

2 hours ago, Murray_Calavera said:

If an OEM MAF is expensive (I have no idea what they go for) I would strongly consider putting the money towards an aftermarket ECU and putting the MAF in the bin. 

Also, how do you know the car is running rich? Do you have a wideband o2 sensor setup?

Interesting ok I’ll look into that as an a new OEM MAF is around 700 USD. And it’s just based on how the car is acting such as very low mpg and a rough idle for reference

6 hours ago, Connorrd said:

Interesting ok I’ll look into that as an a new OEM MAF is around 700 USD. And it’s just based on how the car is acting such as very low mpg and a rough idle for reference

Holy jesus christ! Yeah I would not be spending that on a piece of dinosaur technology. 

Surely you have plans to modify the car in future? You'll need an ECU very quickly on this modification journey anyway, way better money spent on the ECU rather then the MAF (that will end up in the bin anyway, even if it does work, once you install an aftermarket ECU. Just think how painful it will be for future you, throwing a working $700 part in the bin). 

The other option is to go the Nistune route. Buy R35 AFM and adapter tube (for <<$700). Spend >>$700 on Nistune install. Switch from stock AFM to R35 in the software, boost off into the sunset.

Not necessarily better than the full ECU router (in fact definitely not cheaper than the full ECU route) but definitely going to be cheaper to get from "What the f**k is wrong" to "It's working now".

5 hours ago, tridentt150v said:

How much dinero would you spend on a DE? 

IMO return it to stock, stop trying to mod it for 'powa', it is just not worth it.

Luckily it hasn’t been modded a lot pretty sure only thing previous owner did was a CAI and the straight pipe - just hoping to get it running smoothly again

7 hours ago, Murray_Calavera said:

Holy jesus christ! Yeah I would not be spending that on a piece of dinosaur technology. 

Surely you have plans to modify the car in future? You'll need an ECU very quickly on this modification journey anyway, way better money spent on the ECU rather then the MAF (that will end up in the bin anyway, even if it does work, once you install an aftermarket ECU. Just think how painful it will be for future you, throwing a working $700 part in the bin). 

 

7 hours ago, GTSBoy said:

The other option is to go the Nistune route. Buy R35 AFM and adapter tube (for <<$700). Spend >>$700 on Nistune install. Switch from stock AFM to R35 in the software, boost off into the sunset.

Not necessarily better than the full ECU router (in fact definitely not cheaper than the full ECU route) but definitely going to be cheaper to get from "What the f**k is wrong" to "It's working now".

I was looking into a Nistune ECU would it be better for the AFM one or should I look into a 25det and Nistune that? I do have plans to make power hopefully in the future but no point in trying to make power when the car doesn’t run well in the first place

Well.....it's an NA. So there is no point in spending a single dollar on trying to make it go faster, because it won't. You can make it louder, and that's about it.

Don't buy another AFM for it yet. The one you have might be a piece of shit, or it might be OK. Put that to one side for the moment. See if you can locate someone with a known good genuine one that you can test run.

The CEL issue could still be cat related, particularly the overtemp sensor problem I called out earlier that no-one seems to have noticed. I would look into that first. You should also consider the O2 sensor as a likely candidate for running rich.

Ideally you'd take it to a mechanic who has a good scan tool and you'll be able to watch the AFM voltage and the O2 sensor voltage as it is driven and see if they make sense.

10 hours ago, GTSBoy said:

Well.....it's an NA. So there is no point in spending a single dollar on trying to make it go faster, because it won't. You can make it louder, and that's about it.

Don't buy another AFM for it yet. The one you have might be a piece of shit, or it might be OK. Put that to one side for the moment. See if you can locate someone with a known good genuine one that you can test run.

The CEL issue could still be cat related, particularly the overtemp sensor problem I called out earlier that no-one seems to have noticed. I would look into that first. You should also consider the O2 sensor as a likely candidate for running rich.

Ideally you'd take it to a mechanic who has a good scan tool and you'll be able to watch the AFM voltage and the O2 sensor voltage as it is driven and see if they make sense.

Ok I’ll look into that I think - I was considering buying a scan tool also like nisscan and I’ll see what’s up with the O2 sensor someone else in person suggested I should replace it or at least give it a proper cleaning. Luckily theres a local skyline group so should be able to get in contact with someone and see if they can lend a hand

5 hours ago, Connorrd said:

Ok I’ll look into that I think - I was considering buying a scan tool also like nisscan and I’ll see what’s up with the O2 sensor someone else in person suggested I should replace it or at least give it a proper cleaning. Luckily theres a local skyline group so should be able to get in contact with someone and see if they can lend a hand

Nissan Datascan 1 works well for logging this stuff. I use it all the time. It is a godsend compared to old Toyotas or other OBD1 cars that have zero ECU output over the diagnostic connector. It's super helpful to know what the ECU is actually seeing/commanding at any given moment.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Old Son, did you re-use the Holden ABS in the new shell or try a different module?
    • Yeah, nah. I had the actuator rod off it today. The arm will not move at all. Neither out, nor in. Yeah, you'd think so, but I've been thinking about that. Even when the actuator rod fell all the way off at the beginning of this saga, it would build more boost and faster in lower gears than it would in higher gears, and you'd think that that was the opposite of what should happen. But I strongly suspect that there is a thing with the gearing getting the revs to rise faster, that there must be some transient effect with the gas flow rate rising quickly, that you don't get with the more steady state case of the higher gears. Keep in mind - the gate is not shut in either of my weirdnesses. So things are not "normal". We normally think about a turbo spooling up (below the wastegate target) with the gate shut. I have all sorts of mental models running now where the gate is a little bit open, and having it stuck open allowing gas out while it should be going through the turbine has all sorts of weird effects (in these mental models). I'm thinking in the higher gears, the ex mani pressure builds to the point where enough gases spill out the wastegate to just prevent the pressure rising much more at all, or just creeping up, all the whole the revs are increasing and getting closer to the point where a gear shift becomes necessary.
    • Is it possibly wastegate actuator itself is sticking, or even the rod to flapper? Otherwise I reckon things are getting a bit rusty/worn   Also odd it won't boost in 3rd to 5th, but will in 1st, I'd expect the other way around with it slightly open as there's more time on your way to redline for it to spin up
    • Does anyone know ow what these two plugs are for and if they should be unplugged? Just put the dash back together and can't remember if these were plugged in before or unplugged! (Blue and white plugs) 🤦🏽‍♂️
    • Did some FASTing ...got the impression that the actual part# was a moot point ; seems all of these hardlines for coolant are discontinued/NLA... like, I take it you're after the hardline that bolts onto to the manifold...that's NLA according to amayama & nengun .... ...just to clear up some confusion, they typically mounted the AAC valve to the intake manifold somewhere near a coolant passage, so the body of the valve heats up & holds it open when engine's up to temp - no coolant flows through the valve, it's a mechanical, thermal connection.
×
×
  • Create New...