Jump to content
SAU Community

Recommended Posts

Hello again I just got my rb25 tuned yesterday made 450 forged internals and semi built head I went on a beer run and let the car warm up before I got on it and I did a small pull and then about a minute later the engine shut off. I towed it back to the house and been tearing into it today. It’s odd I cant turn the engine by hand to the right (intake to exhaust side) it has some wiggle then it stops and won’t turn any more but I can turn it to the left no problem. I did a leak down and all cylinders were in good condition. I’m so lost at this point. I checked cams in case they snapped and they are all good too. I think I’m going to pull the head off tomorrow just to see what’s going on because I don’t understand.

Link to comment
https://www.sau.com.au/forums/topic/485778-rb25-blown/
Share on other sites

Well, it's too weird to be making any guesses. I'd have the plugs out and a borescope into the cylinders before doing anything else.

When you say

51 minutes ago, Prof_Finesser said:

I can turn it to the left no problem

Do you mean to say that you can turn it over continuously? Like, it's not seized or blocked from rotation outright? Only won't turn forwards? If so, would sound perhaps like something has dropped into the timing belt area or has otherwise arranged itself like a ratchet pawl, so that it prevents rotation one way, but not the other.

Link to comment
https://www.sau.com.au/forums/topic/485778-rb25-blown/#findComment-7992553
Share on other sites

3 minutes ago, GTSBoy said:

Well, it's too weird to be making any guesses. I'd have the plugs out and a borescope into the cylinders before doing anything else.

When you say

Do you mean to say that you can turn it over continuously? Like, it's not seized or blocked from rotation outright? Only won't turn forwards? If so, would sound perhaps like something has dropped into the timing belt area or has otherwise arranged itself like a ratchet pawl, so that it prevents rotation one way, but not the other.

Yes and that’s what I think as well and yes the rotation is continuous 

Link to comment
https://www.sau.com.au/forums/topic/485778-rb25-blown/#findComment-7992554
Share on other sites

3 minutes ago, Dose Pipe Sutututu said:

Most likely won't hold pressure, however it is still possible if the valve isn't bent

I just realized something I’m at TDC and my intake cam is at the timing mark the horizontal mark and my exhaust cam is at like 7-8 o’clock position not even close to the timing mark. I’ve timed these engines about 5 times now and always do it the same line up the 3 marks crank and two cam. How tf have my cam spun that far off. I’m gonna check all the timing system tomorrow 

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/485778-rb25-blown/#findComment-7992567
Share on other sites

3 hours ago, Prof_Finesser said:

I just realized something I’m at TDC and my intake cam is at the timing mark the horizontal mark and my exhaust cam is at like 7-8 o’clock position not even close to the timing mark. I’ve timed these engines about 5 times now and always do it the same line up the 3 marks crank and two cam. How tf have my cam spun that far off. I’m gonna check all the timing system tomorrow 

Many possibilities, like cam gears coming free of the cam shaft and spinning.

Link to comment
https://www.sau.com.au/forums/topic/485778-rb25-blown/#findComment-7992575
Share on other sites

So good news and bad head is off. Good news engine is turning again forwards continuously and pistons have very small mark on the top where valves hit it does catch a finger nail going to still ask machinist if it’s ok to run I think they will be ok.  On to the bad I took the exhaust cam off because the exhaust valves where the only on the pistons and it seems like my first cam cap (closest to timing gear) was eating into the camshaft and end up stopping it all the valves have the marks in picture. 
 

IMG_4302.jpeg

IMG_4303.jpeg

Link to comment
https://www.sau.com.au/forums/topic/485778-rb25-blown/#findComment-7992588
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, the latter. No diff should have a centre replaced without checking clearances because its unlikely to be the same as whatever came out. Not that that stops most people just checking a new centre in
    • Major thread necro but how bad of a job is it to DIY? Looking at it online it looks like if you reuse your ring and pinion as long as those are in good condition it should be fine to just pull the axles/front cover and replace the diff that way? Or should I be replacing everything and doing preload measurements/gear mesh testing like the factory service manual mentions for the rear diff?
    • in my list I had the R33 GTR as the best Skyline. Infact I had all GTR's (33>34=32), the NSX, the GTO, the 300ZX, the 180SX, the S15 better than the FD RX7. I had the MR2 and the A80 as 'just' better. I also think the DC5R Integra looks better but this is an 01 onwards car. I also think the FC>FD. It's almost like aesthetics are individual! The elements @GTSBoy likes about the FD and dislikes about the 180 are inverse in my eyes. I hate the rear end of the FD and it's weird tail lights that are bulbous and remind me of early hyundai excels. They are not striking, nor iconic, nor retro cool. The GTO has supercar proportions. I maintain these look much better in person (like the NSX) especially with nice wheels and suspension which is mandatory for all cars pretty much. Some (or all) of these you have to see in person to appreciate. You can't write a car off until you see one in the flesh IMO. Like most people we probably just like/dislike cars which represent certain eras of design or design styles in general. I also think the 60's Jag E type looks HORRIBLE, literally disgusting, and the 2000GT is nothing to write home about. FWIW I don't think the Dodge Viper Gen1's have aged very well either. You can probably see where I rate bubbly coupes like the FD. I know we're straying now but the C4 and C5 absolutely murder the Viper in the looks department as time goes on, for my eyes. Wouldn't surprise me if people who love the FD, also love the MX5, Dodge Viper, Jag E Type, etc etc.
    • I used to hate R31s, and any of the other Nissans that led up to it, and any of the Toyotas with similar styling, because of the boxiness. They were, and remain, childish, simplistic, and generally awful. I appreciate R31s a lot more now, but only the JDM 2 door. The ADM 4 door (and any other 4 door, even if they are unique compared to our local one) can eat a bowl of dicks. The Aussie R31 is also forever tarnished by their association with stereotypical bong clutching Aussie R31 owners of the 90s and early 2000s. I think the Nissans of the 70s (other than 120Y/180B/200B) are far superior looking to the 80s cars. The 240K era Skylines are boss. The same is broadly true of Toyotas. Hondas don't ever register in my thinking, from any era. Mitsus are all horrid shitboxen in any era, and so also don't register. Subarus are always awful, ditto. Daihatsus and Suzukis also don't generally register. They are all invisible. I think the SW20 MR2 looks fiddly. The 3000GT/GTO is like that but way worse. Too many silly plastic barnacles and fiddly gimmicks ruined what could have been a really nice base shape. Kinda-sorta looks like a big heavy ST165 Celica coupe (and I'm not sure if that's a good thing or a bad thing). I think the 180SX is dreadfully bland. It's not bad looking. But it has no excitement to it at all. It's just a liftback coupe thing with no interest in its lines, and bad graphical elements (ie wide expanses of taillight plastic on the rear garnish). The S13 Silvia is a little better - getting closer to R32 shapes. But still....bland. S14? Nope. Don't love it. S15...a little better. Probably a lot better, actually. Benefits from not being like a shrunk in the wash R34 (where the S13 was a shrunk in the wash R32 and the S14 looked like a Pulsar or something else from the stable on Nissan mid 90s horrors). The Z32 was hot as f**k when it came out but hasn't aged as well as the A80. Keep in mind that I think the R33 is the most disgusting looking thing - and out of all the previous cars mentioned is objectively closest to my precious R32. It's just....real bad, almost everywhere you look. And that is down to the majority of what was designed in the 90s being shit. All Nissans from that era look like shit. Most other brands ditto. In that context, the FD absolutely stands out as being by far the best looking car, for reasons already discussed. Going behind the aesthetics, the suspension alone makes it better than almost any other car.  
    • If they just called it the "Mazda Tiffany", it would have been spot on.
×
×
  • Create New...