Jump to content
SAU Community

AC Compressor


kevboost7
 Share

Recommended Posts

12 minutes ago, soviet_merlin said:

I see some more modern setup being sold as an upgrade and I wonder whether it would make it drive like AC in a modern car. Where you don't really hear it or notice it.

Sadly, it won't happen. The AC controls in our cars are essentially on-off. Whereas the AC in new stuff is more a case of variable displacement compressors giving infinitely variable output.

  • Sad 1
Link to comment
Share on other sites

1 hour ago, GTSBoy said:

Sadly, it won't happen. The AC controls in our cars are essentially on-off. Whereas the AC in new stuff is more a case of variable displacement compressors giving infinitely variable output.

Lots of this, and in older cars, AC is generally controlled by the AC knobs and programming, and the ECU reacts to the load.

Modern cars, the ECU controls kicking the AC on/off at the AC systems request so it can be prepared for the engagement/disengagement.

Link to comment
Share on other sites

17 hours ago, soviet_merlin said:

I went and got the aircon regassed in the Stagea today and asked the guy about the upgrade to the Toyota Echo compressor. He was saying it is likely not going to be as good. It is newer but smaller and not going to pump as strongly. And it would be better to try and get a new OEM compressor. He was saying that the improvements people are seeing may be more likely due to regassing the system. I thought it was interesting to hear.

Going by the sticker the system in my car was last checked in 2015. Gas was at 50% which is apparently beyond terrible. Under 80% is where efficiency already falls apart.

Anyways, with fresh gas the AC is now bloody freezing. I think it may be working a bit less hard as well. I need to drive it a bit more to try it properly. Previously on hill starts it would utterly bog down the car. I'm hoping this is a bit better now.

The frenchies kit looks great, but $1400 for the compressor upgrade alone makes it a bit of commitment. Very much so compared to a $150 regas.

I was thinking the same thing when i saw the size of the smaller Toyota Compressor, but i'm not an AC expert. Where did you take it to get re-gassed? 

Link to comment
Share on other sites

16 hours ago, GTSBoy said:

I don't know if anyone was seriously suggesting a retrofit of an Echo compressor in place of a more-or-less working original comp. You'd have to change the hoses at the bare minimum to do so, and that will definitely add significant cost. I had to get my hoses modded when I did the engine transplant and chose to use the Neo's AC over the even older R32 comp. That was startlingly more expensive than expected for what looks like a simple welding job, and a massive pain in the arse when it turned to have a pinhole leak in the weld too.

The Frenchie's kit is for people who have next to nothing of the original system or have more than that but some of it is a bit shit and better off thrown away than salvaged. If you've got 90% of the system, you just patch it up. Mine is currently degassed because it apparently has a big leak somewhere. If I find it is the compressor, I will be looking to take my spare comp to a shop to assess and/or recondition, rather than contemplating a retrofit to anything off-brand.

After reading this and a few other comments, i'm starting to realize something...

Since i got the car, the AC belt was never put on. I installed the belt on a few months ago because i was tired of melting in the hot car. Once i installed the belt, i was troubleshooting the AC and was turning the red switch on/off while driving the car to see if anything was happening. 

The engine was rebuilt by shop before i purchased the car and the shop might not have re-gassed the AC. Which means i was running the AC without any gas/refrigerant inside the compressor. The AC compressor now acts as if its seized up. I'm starting to think, i caused this damage. 

Link to comment
Share on other sites

4 minutes ago, kevboost7 said:

Which means i was running the AC without any gas/refrigerant inside the compressor. The AC compressor now acts as if its seized up. I'm starting to think, i caused this damage. 

Yup. She's toast. You need refrigerant to carry the compressor oil to stop the thing from welding itself together.

  • Like 1
Link to comment
Share on other sites

9 hours ago, kevboost7 said:

I was thinking the same thing when i saw the size of the smaller Toyota Compressor, but i'm not an AC expert. Where did you take it to get re-gassed? 

I have heard the frenchys kit (with the smaller toyota compressor) performs fantastic. i havent actually gassed my system yet, so cant confirm myself..

Link to comment
Share on other sites

On 24/09/2024 at 7:49 AM, kevboost7 said:

Where did you take it to get re-gassed? 

I went to a local car aircon workshop: https://aceautoelectrical.com.au/

Took all of 30 minutes to get in, check, regas and leave again.

Might be a bit of a drive for you :D But I presume any shop specialising in aircon should do. And I guess they'd be able to confirm whether the compressor is stuffed or not.

Link to comment
Share on other sites

15 hours ago, soviet_merlin said:

I went to a local car aircon workshop: https://aceautoelectrical.com.au/

Took all of 30 minutes to get in, check, regas and leave again.

Might be a bit of a drive for you :D But I presume any shop specialising in aircon should do. And I guess they'd be able to confirm whether the compressor is stuffed or not.

Thats the problem, this car in the states gets more attention than lamborghinis and ferarris. I have yet to take this car to any shop because i'm afraid they will take it for joyrides. I need to do an alignment but i've been holding off. 

Link to comment
Share on other sites

On 9/23/2024 at 5:59 PM, GTSBoy said:

Yup. She's toast. You need refrigerant to carry the compressor oil to stop the thing from welding itself together.

f**k my life.. this whole time i thought the AC was just broken, but now realizing that i probably broke it myself is really hitting me

  • Like 1
Link to comment
Share on other sites

7 hours ago, kevboost7 said:

Thats the problem, this car in the states gets more attention than lamborghinis and ferarris. I have yet to take this car to any shop because i'm afraid they will take it for joyrides. I need to do an alignment but i've been holding off. 

It sounds like by avoiding maintenance you may be doing more damage than a hypothetical guy in a workshop taking it for a spin.

Not sure if you are just being paranoid or things are actually that bad in the US. Find a reputable shop not run by dickheads. Look for people that take pride in their work. Stick around for the day if you have to :)

Link to comment
Share on other sites

10 hours ago, kevboost7 said:

I need to do an alignment but i've been holding off. 

1 hour ago, soviet_merlin said:

Not sure if you are just being paranoid or things are actually that bad in the US. Find a reputable shop not run by dickheads.

Yes, well, wrt a wheel alignment, there are two types.

Either: You have very little added adjustables, in which case the alignment can be done by anyone in any tyre shop or equivalent, and will only take 30 minutes, and so there is no reason to even consider leaving the car there.

OR: The alignment is a major exercise because you have adjustables everywhere and so you will need to be taking it to a shop that is skilled and experienced at setting up race cars and the like, and you won't need to worry about leaving the car there.

Link to comment
Share on other sites

On 26/09/2024 at 12:17 PM, GTSBoy said:

OR: The alignment is a major exercise because you have adjustables everywhere and so you will need to be taking it to a shop that is skilled and experienced at setting up race cars and the like, and you won't need to worry about leaving the car there.

100% this. Long ago, I had a guy from the R31 club who set my BNR32 up (adjustable arms all round). He did an awesome job, was an after-work kinda thing where I had to bring a slab of beer. My car never drove better, and I stupidly got a random tyre shop to check the toe angles when I changed tyres, and they ruined the alignment.

tl:dr- it takes a lot of skill to set up your car lowered from factory properly, and is worth paying the $200+ it takes.

Link to comment
Share on other sites

  • 2 weeks later...
On 9/25/2024 at 8:26 PM, soviet_merlin said:

It sounds like by avoiding maintenance you may be doing more damage than a hypothetical guy in a workshop taking it for a spin.

Not sure if you are just being paranoid or things are actually that bad in the US. Find a reputable shop not run by dickheads. Look for people that take pride in their work. Stick around for the day if you have to :)

I'm a bit paranoid, but i've caught a normal car dealership in which i bought my truck (Ford F-150). I dropped it off in the morning and when i returned, i found the car had 100 more miles on it. I know that alignments don't take 100 miles. 

Link to comment
Share on other sites

1 hour ago, kevboost7 said:

Find a reputable shop not run by dickheads.

1 hour ago, kevboost7 said:

normal car dealership

These are far from the same thing. They are, in fact, about as far apart, in this context, as it is possible to be.

  • Like 1
Link to comment
Share on other sites

Depends on the dealership and staff working there.

Have personally worked at 2 dealerships and have know great mechanics and bad ones.

The biggest issue is a good mechanic can normally get paid more through a private workshop, so will take that over dealership jobs. But sometimes theyre happy where they are doing what they're doing.

Dealerships deal with current cars due to warranty scare tactics and prices, so anything aging gets harder to find people who know the product (staff turnover) 

Link to comment
Share on other sites

AAAaaaaarrrrrrggggghhhhh!

Following on from OP's AC woes....mine got regassed last year and at some point I discovered it had lost enough gas to not switch on any more. It had dye in it, but we never saw any trace of dye, perhaps because it all fell out long enough before we looked that it washed away. (Or, shudder, it's under the dash in a hard to see/reach spot!). I almost never run the AC because I just drive with the windows down even when it's 40+ outside. Only occasionally want it when I just can't take the heat or if I need some defog.

So, got it gassed up again with more dye and oil so I could run it a bit to provoke the leak to show.

And the compressor is noisy.

So, now I am staring down the barrel of having to fit a rebuild kit to the compressor (or maybe the spare that is on the shelf).  And hope that the leak is at the comp, and not under the bloody dash.

Link to comment
Share on other sites

On 10/21/2024 at 7:55 PM, GTSBoy said:

AAAaaaaarrrrrrggggghhhhh!

Following on from OP's AC woes....mine got regassed last year and at some point I discovered it had lost enough gas to not switch on any more. It had dye in it, but we never saw any trace of dye, perhaps because it all fell out long enough before we looked that it washed away. (Or, shudder, it's under the dash in a hard to see/reach spot!). I almost never run the AC because I just drive with the windows down even when it's 40+ outside. Only occasionally want it when I just can't take the heat or if I need some defog.

So, got it gassed up again with more dye and oil so I could run it a bit to provoke the leak to show.

And the compressor is noisy.

So, now I am staring down the barrel of having to fit a rebuild kit to the compressor (or maybe the spare that is on the shelf).  And hope that the leak is at the comp, and not under the bloody dash.

Did you re-gas yourself? And i'm not familiar with the leaking points. What if its leaking under the dash? I'm assuming this is a pain in the ass job to fix? 

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • Right.  I'll try my best at a concise "bring you up to speed" on stuff that may be missing here - obviously open to questions or further input from others as relevant. Here's a datalog from a responsive turbo setup with electronic boost control being used a bit, to keep it simple I've marked 3 points of interest.  All of these charts are on the same time scale on the X-axis, so you can reference what engine rpm is doing in the top graph, boost and EMAP (exhaust backpressure) in the second graph, and turbo rpm in the bottom graph. A) The turbo gets it's power from exhaust gas, and pumping air takes work.  As a result you can't just spin a turbo with a fixed amount of exhaust energy and expect it to keep spooling - the bigger the turbo (ie, the more air it can push) the more exhaust energy you need to drive it.   The most obvious ways of getting more exhaust energy are by adding displacement, adding boost, or adding rpm - but as you add any of these the turbo also needs to do a bit more work so there is a big balance of these things needed to even get to your target boost and sometimes that's not even possible. What you can see in step "A" is that there isn't enough engine rpm or boost to reach the level we want, so this is where "lag" is.  The dyno run continues and rpm increases, which gives enough energy to increase boost, which helps spool  the turbine speed up even more - so you can see that the rate that the boost (and turbo speed) are starting to ramp up faster than the engine rpm is, so turbo is really starting to wake up as the graph gets closer to point B....   B) At this point we've been able to reach the boost that is actually desired at this point.   To stop the boost from going further than this the wastegate will open and bypass gas past the turbine, meaning it doesn't continue accelerating at the point it was before but instead carry on at a more progressive rate which matches what the engine needs.   The wastegate will have a spring in it which is rated to a specific pressure where it will start bypassing, but electronic boost control (managed by the ECU) can adjust how much pressure the spring sees in order to allow some tunability on how much boost the wastegate actually sees, and therefore how much exhaust it bypasses.   The tune in this case stops boost from ramping up HARD at around 21-22psi just before 4000rpm, then as the rpm continue it allows boost to continue up to around 25psi higher in the rpm.   You can see the turbo speed fairly steadily increases through the rpm to ensure it's keeping up with the increasing airflow demand due to the engine speed being higher and boost being pretty steady.   If the boost dropped off after a point then you may see the turbo speed level off or even drop.   C) You can see that despite the boost pressure staying pretty flat here, the exhaust pressure is steadily increasing and at this stage has overtaken boost pressure.   This isn't unusual, and is largely as a result of the increasing energy needed by the turbo to pump more and more air to suit the needs of the engine as it revs out further.   There are a bunch of variables in regards to how much back pressure there will be on a given turbo etc, but its one of the factors we manage when sizing and tuning a turbo setup.   When exhaust back pressure starts exceeding boost pressure you will eventually start seeing signs that the turbo is running out, the engine gets less keen to make more power and it gets harder to raise boost further. In this case it's a fairly acceptable compromise for the power level (around 630kw on a 3litre engine with full boost by 4000rpm), but you'd not want to push it a lot harder than this.  The maximum speed rated for the compressor wheel on this setup is around 125,000rpm so you can see its starting to get close on that side as well - I feel like this kind of illustrates some of the turbo related things we both decide on how far to push, and are also limited to how far we can push depending on the parts combination. Hope this helps more than it confuses things  
    • For that influx of Spammers we had I made no pic posting and no PM's for first ten posts. This is group based and I've manually updated @Beanie to the Members group which will open up the images and PM's. 
    • Thx for the reassuring reply. I’ve got above legal clearance  going in for roadworthy Friday… fingers crossed it’s keeping me awake  bloody nanny state 
    • I was actually going to try and dig out a datalog with turbine speed and EMAP haha
    • Wait until @Lithium posts a compressor map and tries to explain what's going on. There is a strong possibility that the OP lives in a digital world and is not comfortable with analogue machines. A turbo is just about as analogue as it gets, with plenty of non-linear behaviours added in on top. Most of us who think we know how they work are actually only getting by on 2nd and 3rd order mental models that abstract away from the actual physics and bring it back to the sort of kindergarten level concepts we can hold in our heads. This is important when you need to hold 10 such concepts in your head at the same time. You need to reduce the complexity of the individual concepts to allow them to be simultaneously held and manipulated. Too much complexity in the base models makes it very difficult to make them work with each other mentally.
×
×
  • Create New...