Thinking of getting a Q50 300hp and just tuning it instead of getting the Q50 Red or 400R

[180 wanabe]

So next year I am looking at upgrading from my VE SS bomadore ute to something more refined. 

I wanted to stick with a V8 but not anything German or Australian, either a coupe or a sedan.

So if I wanted anything newish that limited my options to either the Lexus RCF which I quite like. But with the price they demand and a kid on the way a 2 door coupe is probably not going to be the best idea.

The next best thing would be the ISF but the newest models are 2014 and commanding over 60k and even the older 2008 models in ok condition starting around 35k is kind of bullshit.

So I figured if I could not have the noise I could perhaps make do with easy power. Enter the infinity Q50 or Skyline equivalent.

The price difference between the 300 and 400hp models seems a bit crazy.

Right now there is 300hp Q50 one on carsales from a dealer with 61km for 27k drive away. If I wanted to get a 400hp Red or 400R car the prices seem to start at 43k

From my limited research it seems that the only differences are that the 400r/Red

1. Red runs more boost and a more aggressive tune.
2. There are are turbine speed sensors on the turbos.
3. Has 2 pumps for the water to air intercooler.
4. Runs an engine oil cooler.

I'm guessing that the exterior trims might look a little more sporty as well.

I had a lazy look for upgrades to bridge the gap on z1motorsports

They have kits that upgrade the water to air heat exchanger as well as the coolant pump which should give a non Red/400r better intercooling temps than the stock Red/400r. I added an engine oil cooler with a thermostat as well to try and make things as close as possible. Obviously the ECU is going to need a tickle. Having not done much in the way of research they also sell a ECU flashing tool with pre loaded tunes that are supposed to boost the non Red/400R by 100hp which adds 1k USD to the cost. The total cost of the parts @ the current time including shipping and taxes worked out to be $4350 AUD.

Personally I would rather get the car tuned on a dyno which would probably add more cost

Assuming the worst that you got a workshop to install the new parts I would guess no more than 5 hours would be required in the worst case @ 5 x $150 per hour = $750

So the total cost could be around $5100

So for easy number 5k + 27K = 32k

I guess that would leave some change left over to swap out the open diff and fit a LSD

Any thoughts?

 

 

 

[Duncan]

I reckon you are 100% right on the money.

The only reason I bought Red Sport instead of the base VR30 is that I am investigating racing it in Production Cars, and they require you to run a (mostly) standard car....therefore knowing exactly what was in the RS spec was important to me and I paid the extra.

Other than that, for sure I would have pocketed the $10k and spent them on mods instead. Plus the non-RS models are more likely to have had a nicer life prior. Just a warning though, mods always cost twice as much as they look like they will on paper

BTW you should also consider the 400R imports, they are about the same price as a local RS but 5+ years newer. Of course that comes with the usual warnings about finding parts, unhelpful nissan dealers and finding insurance

[180 wanabe]

1 hour ago, Duncan said:

BTW you should also consider the 400R imports, they are about the same price as a local RS but 5+ years newer. Of course that comes with the usual warnings about finding parts, unhelpful nissan dealers and finding insurance

Yeah I would like to try and get a ADM car to reduce issues with insurance.

I've decided if I end up getting this car I will set it up to be a sleeper build, leave it looking stock/dad spec on the outside

I wonder if you can just drop in the 400r/Red/Z ECU or better still use a flashing tool to copy the map off one. Backup the factory map and then flash the 400hp cars onto the 300hp cars ECU?

[180 wanabe]

Also I'm a little turned off by the engine being only direct injected. If you put a catch can on early enough this should save all the build up on the valves and intake ports ?

Edited 2 hours ago by 180 wanabe

[GTSBoy]

13 minutes ago, 180 wanabe said:

If you put a catch can on early enough this should save all the build up on the valves and intake ports ?

Nah, just slow it down.