Jump to content
SAU Community

R34 GTT Battery Relocation To Trunk

Beanie
 Share

Recommended Posts

Beanie Rookie

Beanie

Posted
Posted

Hi all!

Looking to relocate the battery to the trunk of an R34 GTT.

I want to do it using as many stock GTR components as I can (including the harness protectors from the 34 GTR that run underneath along the chassis to the engine bay). So far I’ve purchased the battery tray from a 33 GTR, as the captive weld nuts are already there just asking to be used.

There is also the slight issue of now having to relocate the ABS/TC/Fuel Pump Control ECU, which in GTT’s sits right above where the battery will then sit on the tray.

Has anyone already achieved this, and if you have any pics that you wouldn’t mind sharing? It would be great to see how others have done it and where you put them, as there are countless holes in the parcel shelf panel to potentially use.

Just trying to get some ideas bounced around, and to help uncover any potential problems I may encounter by  my choice of location.

TIA for any help!

IMG_7220.thumb.jpeg.664141f810ab9be59f651d58881467b3.jpeg

IMG_7221.thumb.jpeg.19bbf190d6436a49102f5488da08bdcd.jpeg

IMG_7222.thumb.jpeg.1fb4967d9e1e796adf3100ad01babeae.jpeg

Link to comment
https://www.sau.com.au/forums/topic/485936-r34-gtt-battery-relocation-to-trunk/
Share on other sites
Beanie Rookie

Beanie

Posted
  • Author
Posted

I believe there was a similar one posted by @duggyphresh.

They were re-routing their battery positive cable in the way I am also trying to achieve.

Sorry, I’m new to this forum, so was a bit late to the party by a few months and so reignited the old thread, as I wanted to know how they got on with doing it.

  • 1 month later...
NZ-GTT Collaborator

NZ-GTT

Posted
Posted

I did this mod in 2019 

You just have to modify the top bracket of the ABS/TC/Fuel Pump Control ECU so it sits more upright and closer to the back seat and run a good quality positive battery lead from the engine bay, the negative lead i just bolted down to the body in the boot.

Watermouse Collaborator

Watermouse

Posted
Posted

I just got this system but haven’t installed yet

I got a Moroso sealed box (defect reasons) which will be set up same as their pic

The quality is high grade, the correspondence I had with the owner (former head designer for Rockford Fosgate) was unbelievable, guiding me with what I needed. Even told me not to buy some things as it could be sorted in a different way at his loss.

Just a bit of a bite with the exchange rate and don’t purchase gear in 1 hit that goes over $1,000 au, lol I forgot!

 

IMG_0607.png

IMG_0608.png

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      New fix for low tyre pressure from bmw

      By MBS206 · Posted

      Yep, pretty much what you said is a good summary. The aftermarket thing just attached to the rim, then has two lines out to valve stems, one to inner wheel, one to outer wheel. Some of the systems even start to air up as you head towards highway speed. IE, you're in the logging tracks, then as speeds increase it knows you're on tarmac and airs up so the driver doesn't even have to remember. I bet the ones that need driver intervention to air up end up seeing a lot more tyre wear from "forest pressures" in use on the highway!
    • sunsetR33
      Anyone know this frontpipe?

      By sunsetR33 · Posted

      Yes, but you need to do these type certifications for tuning parts. That is the absurd part here. Meaning tuning parts are very costly (generally speaking) as well as the technical test documentation for say a turbo swap with more power. It just makes modifying everything crazy expensive and complicated. That bracket has been lost in translation many years ago I assume, it was not there.
    • dbm7
      New fix for low tyre pressure from bmw

      By dbm7 · Posted

      Hahaha, yeah.... not what you'd call a tamper-proof design.... but yes, with the truck setup, the lines are always connected, but typically they sit just inside the plane of the rear metal mudguards, so if you clear the guards you clear the lines as well. Not rogue 4WD tracks with tree branches and bushes everywhere, ready to hook-up an air hose. You can do it externally like a mod, but dedicated setups air-pressurize the undriven hubs, and on driven axles you can do the same thing, or pressurize the axles (lots of designs out there for this idea)... https://www.trtaustralia.com.au/traction-air-cti-system/  for example.... ..the trouble I've got here... wrt the bimmer ad... is the last bit...they don't want to show it spinning, do they.... give all the illusion that things are moving...but no...and what the hell tyre profile is that?...25??? ...far kernel, rims would be dead inside 10klms on most roads around here.... 😃
    • joshuaho96
      Anyone know this frontpipe?

      By joshuaho96 · Posted

      You're just describing how type certification works. Personally I would be shocked to discover that catalytic converter is not in the stock mounting position. Is there a bracket on the transfer case holding the catalytic converter and front pipe together? If so, it should be in stock position. 
    • GTSBoy
      New fix for low tyre pressure from bmw

      By GTSBoy · Posted

      You talking about the ones in the photo above? I guess that could make sense. Fixed (but flexible) line from the point up above down to the hubcap thingo, with a rotating air seal thingo. Then fixed (but also still likely flexible) line from the "other side" of the transfer in the hub cap thingo up to the valve stem on the rim. A horrible cludge, but something that could be done. I'd bet on the Unimog version being fed through from the back, as part of the axle assembly, without the need for the vulnerable lines out to the sides. It's amazing what you can do when you have an idea that is not quite impossible. Nearly impossible, but not quite.
×
×
  • Create New...