Jump to content
SAU Community

Recommended Posts

I had my car for over 10 years and done around few thousand miles but never changed the oil. thinking of changing it.

 

what brand and viscocity would you put in ? people seem to use redline shockproof in the diff

 

on  contraty seen others using atf dexron 2 or 3 so wanted to check. is it 1 liter?

Edited by drifter17a
Link to comment
https://www.sau.com.au/forums/topic/485948-r34-diff-oil/
Share on other sites

31 minutes ago, drifter17a said:

people seem to use redline shockproof in the diff

No. Well, some people "seem to use redline shockproof in the diff". Most do not. I would only contemplate it if you have badly worn CW&P gears.

And no. No-one in their right mind has ever put ATF into a diff.

Any normal diff/gear oil of the right viscosity will do. Whatever takes your fancy. Castrol, Nulon, Penrite, Redline MT range. Whatever. It's just gears.

75W-90 or 80W-90 is typical. I think that GL-5 is hard to avoid these days, although I think that a GL-4 is probably preferred, given the vintage of the equipment. At least Redline offer a number of GL-4 oils.

If you have a clutch type LSD instead of the VLSD, then of course you need a proper LSD oil. Anything from any of the same names above.

If you have a helical LSD, then it does not require LSD oil, and the recco is the same as for the VLSD. You don't want the LSD friction modifiers in the oil for a non-clutch type LSD if you can avoid it.

 

Link to comment
https://www.sau.com.au/forums/topic/485948-r34-diff-oil/#findComment-7995189
Share on other sites

I believe mine is helical and not clutch type. During drifting one wheel was spining as if it was open diff so bought kazz 1.5 way and has sat on my shelf for the past 5 years as I want to learn shiming process and do it myself

 

in meantime thought I change the diff oil hence post here. So any 75-90?

 

i am pretty sure r34 are helical not clutch lsd as standard . That is gtt ones

Link to comment
https://www.sau.com.au/forums/topic/485948-r34-diff-oil/#findComment-7995191
Share on other sites

99.9% of them are viscous diffs. The 0.01% are helicals. They were only option-able in the series 2, as well.

I have redline heavy shockproof in my helical. It seems... fine? I don't think anyone is ever going to know until something really breaks and at that point I'm not sure anyone will blame the oil. I just chose it because it's extremely heavy duty and my car will see not-road-legal duty for it. I've also had sadness with various diff oils in the past sweating out everywhere and/or other 'fun' things, with clutch diffs.

Given you have a 1.5 way on the shelf, I'd not even bother with the diff in the car and just get to tinkering with it. I would spend the $90 on oil toward the labor of someone else putting the diff in if time poor even lol.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/485948-r34-diff-oil/#findComment-7995192
Share on other sites

1 hour ago, drifter17a said:

I believe mine is helical and not clutch type. During drifting one wheel was spining as if it was open diff so bought kazz 1.5 way and has sat on my shelf for the past 5 years as I want to learn shiming process and do it myself

 

in meantime thought I change the diff oil hence post here. So any 75-90?

 

i am pretty sure r34 are helical not clutch lsd as standard . That is gtt ones

75W90 GL5 is fine. If you aren't sure about the type get one with LSD additive. 

Link to comment
https://www.sau.com.au/forums/topic/485948-r34-diff-oil/#findComment-7995194
Share on other sites

2 hours ago, drifter17a said:

believe mine is helical and not clutch type.

Unlikely, as per Greg's post.

2 hours ago, drifter17a said:

During drifting one wheel was spining as if it was open diff

This is not helical diff behaviour unless one wheel is up off the ground.

2 hours ago, drifter17a said:

I want to learn shiming process and do it myself

Shimming what? You don't "shim" a mechanical LSD. Probably not in the sense that you have heard of people "shimming" a diff. And the process that Nissan f**kwits call "shimming" a diff involves super-preloading a VLSD cartridge against the side of the diff to create a friction/wear point (in a place that it wasn't supposed to have one) to make the sloppy, useless, viscous diff into a hybrid viscous/mech abortion.

In case it isn't clear, I consider the process to be stupid.

2 hours ago, drifter17a said:

bought kazz 1.5 way and has sat on my shelf for the past 5 years

Nike.

Link to comment
https://www.sau.com.au/forums/topic/485948-r34-diff-oil/#findComment-7995199
Share on other sites

7 minutes ago, GTSBoy said:

This is not helical diff behaviour unless one wheel is up off the ground.

Sadly I can confirm if you are actually seeking to drift, you will quite easily spin up one wheel. Even if you're going in a straight line. I am not entirely sure of the metrics/terminology here but there's only a certain amount that the helical will actually spin both wheels. I've seen it on video with my own car where two lines of smoke switch over to just one after you really get in to it.

Unlike with a clutch diff where you can keep your foot planted until the car regains grip, in my experience with the helical you want to be utilizing traction control allowing LIMITED slip or lifting (partially) when you start to spin up both tyres with a Nissan helical.

Which makes them pretty sub optimal for drifting duty. That said... this is probably a helical on numbers alone. Just put the Kazz in :D

Link to comment
https://www.sau.com.au/forums/topic/485948-r34-diff-oil/#findComment-7995201
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you put an aftermarket oil pressure gauge on and verified your oil pressure?   Noise being on the block, on exhaust side, how high up the block does it seem to be? It could be the VCT system getting cranky, especially if it's mainly at idle, and when warm, as that'll be your lowest point for oil pressure. Could be showing that oil passages / VCT solenoid are blocking.
    • Well, hydraulic lifters will get noisy if they are dirty/fouled in some way, and exactly how that manifests will depend on exactly what schmutz is where. There is a procedure on here somewhere for dismantling and soaking/cleaning them. Replacing them with new is about 50% of the work and about 5% of the money!
    • Thanks for the reply @GTSBoy this is is a hydraulic lifter engine. Yea right i did not realise the lifters were supposed to be compressible while installed. I could push them down but i had to lean almost my while body weight on them.  I have never heard of a lifter/ lifters ticking only at hot idle and getting worse the hotter it gets. I have owned a few jdm cars with noisy lifters. This noise is slightly more subtle, it is more of a sharp gentle metalic tic than the solid and more loud tapping I've heard on lifters. I have used a metal rod, alloy tube, hose and stethoscope and could not find the source of the tick. But it appears to be loudest on the actual engine block behind the exhaust cam gear and next to the oil filter. I had mate (40 year old mechanic) go over it with me and he couldn't find it either..  Could it be a cam seal issue of some sort?  Cheers  
    • This seems problematic and unlikely at the same time. Vanilla RB2Xs have hydraulic lifters. They do have "zero" clearance, but only when running with oil pressure inside them. When not running, you should be able to compress them and obtain heaps of clearance. RB26s and Neos have solid lifters. They should have ~0.3mm and ~0.5mm on the inlet and exhaust respectively. If they have zero clearance then bad things are happening. With nothing else being wrong, it would mean that the valves would be held slightly (ever so slightly) open when they are supposed to be closed and it should have all sorts of problems when running, caused by leakage in/out through the valves. Or, zero clearance can indicate severe valve seat recession. None of it is good. Have you used a piece of hose as a stethoscope to try to localise the noise?  
×
×
  • Create New...