Jump to content
SAU Community

R34 RB25 Neo sounds like a diesel

Henrycmk

By Henrycmk,
in R Series (R30, R31, R32, R33, R34)

 Share

Recommended Posts

Henrycmk Newbie

Henrycmk

Posted
Posted

Picked the car up from the dock recently. Fairly low mileage about 100k kms, car looks very well maintained inside and out. Has a hks-gtrs turbo. The car sounds cammed at idle, similar to videos ive found of the tomei 262. There is a very distinct sound coming from cylinder 1 or 2 on the intake side that sounds almost like an exhaust leak or diesel sound. Car drives fine, i have only put about 30 miles on it, still need to do a fluid flush. Any ideas on the sound? Is this how rb25 neos are supposed to sound?https://youtube.com/shorts/eqHXawpgArI?si=v5q8pZQuOrNXYrBQ

Link to comment
https://www.sau.com.au/forums/topic/485995-r34-rb25-neo-sounds-like-a-diesel/
Share on other sites
Henrycmk Newbie

Henrycmk

Posted
  • Author
Posted
6 minutes ago, GTSBoy said:

Well, it is an unusual noise. Use a 2 foot long bit of garden hose stuck in your ear as a stethoscope to pin it down to a definite location. We'll never work it out across the internet.

I plan to pull the intake manifold off and check the gaskets, i read that the block to manifold gasket can blow over 14psi and when i picked up the car it was set to 1.2bar on the controller. Send the injectors out for cleaning. Ill also pull the cam covers off and do an inspection, check some valve lash. Someone also said that the timing belt can rub or vibrate against the belt cover and make that sound. Definitely need to get an AFR gauge on it, if it was lean idling im sure it wont be happy

GTSBoy Grand Master

GTSBoy

Posted
Posted
46 minutes ago, Henrycmk said:

i read that the block to manifold gasket can blow over 14psi and when i picked up the car it was set to 1.2bar on the controller.

Yeah, nah. Not a thing.

The gasket between the top of the plenum and the runners is far more likely to blow out when it gets old, and not really at ~14 psi. These things have been run to double that for 30 years without that being a common thing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R32 update from 1990's spec.

      By Duncan · Posted

      Great to hear you are bringing it out of the shed again. Unless you have specific issues I'd just add the wideband, get a good tune and enjoy it. Certainly no point changing coils etc if they are working. If would add fuel pressure and e85 sensor if you are doing a general update but not if it runs OK and you are just getting it back on track. The other thing is smaller, modern twins, -5 are OK for motorsport but pretty laggy and old tech for street use (of course, if performance is the priority a modern single with twin scroll manifold etc is the go but not cheap). The final thing worth considering is switching to an ethrottle if drivability is still an issue, it should make things a lot simpler and smoother
    • Duncan
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By Duncan · Posted

      Yeah pretty sure they are m4, but best to check, and perhaps use new hardware Also don't over torque them......there was that one time I lost an expensive engine after a workshop overtorqued one of those bolts and it ended up in the oil pump (no, I don't know why they removed the intake mesh either)
    • Komdotkom
      Compressor flow comparison table

      By Komdotkom · Posted

      I might have to shoot them an email. Pity the exchange rate is so bad at the moment. BTW, thanks for posting that table makes interesting reading. 
    • robbo_rb180
      R32 update from 1990's spec.

      By robbo_rb180 · Posted

      Add these Sensors -Wideband, Oil Pressure, Fuel pressure, Intake air temp Good inspection of ignition system of coils, plugs and loom (12v feed and good ground)- a r35 kit is best bang for buck upgrade. A decent tuner should be able to see any issues with the trigger system- a link has good filtering but a good simple upgrade is the nz wiring bolt in kit. Check and replace all the fuel filters- you would be surprised at intank filter after a few years. Also good to check for any leaks on vac hoses and pipe work as has been said. No need to go overboard and spend big $$$ to enjoy the car. A quality tuner is getting harder to find as anyone with a laptop thinks they are a tuner. A link has great features to check sensor voltages and frequency inputs and easy to see live by pressing f12. The link can do a TPS & RPM fuel/ignition mapping on ITB cars then add a 4D table with MAP and ability to add a 5D to it (can help with economy at cruise with wheel speed vs TPS) Where are you located as that will help narrow down a good tuner ?
    • Wazmond
      Stagea Automatic Box

      By Wazmond · Posted

      Reviving an old thread, I reckon my stagea is starting to slip. Car usually gets parked on a hill, narrow driveway so cant go up the driveway smoothly, anyhows, lately first gear feels "sluggish"? Not responsive. Feels like I gotta run the engine more than usual to get off the line...  Any recommendations for transmission servicing in Sydney? Or possibly just an excuse to go manual ?
×
×
  • Create New...