NPboosted manifold fitting purpose

[eli995]

I’m trying to figure out the purpose of these fittings. Assuming they’re for coolant but not sure where the lead to. I know the bigger one on the right (which isn’t filled) is the brake booster. If anyone has a photo of a diagram of this intake or has a set of instructions it’d be greatly appreciated 

[Duncan]

I was just going through this on Neil's car (33 gtst). Assuming you are using standard AAC and Cold start valves, you need

Post Turbo Pre throttle to Boost Controller (if you have one) then to Turbo Wastegate

Pre throttle to AAC input

AAC input T piece to Cold start input

Cold start output to plenum post throttle

AAC Output to plenum post throttle

AAC Output to brake booster (needs a 1 way valve)

Plenum post throttle to Fuel Pressure Regulator

Plenum post throttle to Blow off valve signal

Plenum post throttle to Boost controller input (if you have one)

[eli995]

23 minutes ago, Duncan said:

I was just going through this on Neil's car (33 gtst). Assuming you are using standard AAC and Cold start valves, you need

Post Turbo Pre throttle to Boost Controller (if you have one) then to Turbo Wastegate

Pre throttle to AAC input

AAC input T piece to Cold start input

Cold start output to plenum post throttle

AAC Output to plenum post throttle

AAC Output to brake booster (needs a 1 way valve)

Plenum post throttle to Fuel Pressure Regulator

Plenum post throttle to Blow off valve signal

Plenum post throttle to Boost controller input (if you have one)

Ok awesome! I’m not running a aac/iacv (although I do have the r34 iacv but I’m running the heater core loop. I’m running the chase bays booster delete so In that case would I need to block off those posts? So at the moment I need to run from one of the posts to the fpr and then a separate post to the boost controller then to the wastegate? Also I’m assuming that each port has a specific use like the first one farthest to the left would be (for example) manifold to fpr and then second would be to boost controller?

Edited 21 hours ago by eli995

[Duncan]

Sounds like you need these two:

Plenum post throttle to Fuel Pressure Regulator

Plenum post throttle to Blow off valve signal

You can use any of them for anything, just depends what routing is convenient

 

You probably need these too, depends how your boost control works (eg, MAP sensor in the ECU)

Plenum post throttle to ECU or Boost controller input (if you have one)

Post Turbo Pre throttle to Boost Control Solenoid (if you have one) then to Turbo Wastegate

[eli995]

 

Edited 21 hours ago by eli995

[eli995]

18 minutes ago, Duncan said:

Sounds like you need these two:

Plenum post throttle to Fuel Pressure Regulator

Plenum post throttle to Blow off valve signal

You can use any of them for anything, just depends what routing is convenient

 

You probably need these too, depends how your boost control works (eg, MAP sensor in the ECU)

Plenum post throttle to ECU or Boost controller input (if you have one)

Post Turbo Pre throttle to Boost Control Solenoid (if you have one) then to Turbo Wastegate

Ok gotcha, so one post to fpr 

another to bov 

and I have the mishimoto boost controller and a link g4+ so I’d just have the tuner set it up properly. For the last two from plenum post throttle to  ecu/ boost controller, I know that I have a hose coming from the ecu that I was confused about so I assume that’s what connect to the boost controller from the ecu? And then the last is just from plenum to boost controller then to wastegate?

[GTSBoy]

1 hour ago, eli995 said:

I know that I have a hose coming from the ecu that I was confused about so I assume that’s what connect to the boost controller from the ecu?

No. The ECU's hose is for a connetcion between the plenum (assuming single throttle body, not ITBs) and the ECU's internal MAP sensor. This is the primary load measurement of the ECU - so you need to get this one right. This has NOTHING to do with the boost contol.

The wastegate also needs to see a boost signal - but it is actually far better for it NOT TO COME FROM THE PLENUM (again, assuming single TB, and not ITBs). This should come from the turbo's compressor housing (assuming there is a nipple on there, which there might well not be), or on the boost pipe somewhere between the turbo and the TB. On the pipe from the turbo to the intercooler is usually most convenient. The boost controller is then located between that boost source and the wastegate, ACCORDING TO THE CORRECT PLUMBING DRAWING FOR THAT BOOST CONTROLLER. There is no general diagram or instruction that will be correct for every case.

Then the other ports on the plenum are for purposes such as Duncan described. If the boost controller has an internal MAP sensor, for a boost display, etc, then it will want to be hooked up there, alongside the ECU and the FPR.

[Duncan]

Yeah just run one of those posts to the Link like GTSBoy said.

From google it looks like a "mishimoto boost controller" is a manual boost controller. Since you already have the link just buy any MAC valve and plumb it in where the mishimoto is now. Wires to the solenoid should come from the Link's / standard loom boost control wiring (I guess you have an r32, not sure if it is gtst or gtr, if it is GTR where is a 2 pin connector near the engine bay fuse box/injector resistor for that purpose, assuming the standard boost controller is gone)