Jump to content
SAU Community

Oil Presure Problems

DR.ZOIDBERG
 Share

Recommended Posts

DR.ZOIDBERG Proficient

DR.ZOIDBERG

Posted
Posted

Hey

I was driving my R32 GTR and I got held up in some trafic, I was idling at 1k and noticed my oil presure gauge sitting on 0. I thought to myself "FU*K", wtf is going on. When I slowly started to move it would slowly climb up, but the back to 0 when I came to a stop. When we started to move again and we got going, the gauge would sit normal, about 2. When I came to a stop again the gauge went to about 1 and stayed there this time. When I got home it was reading normal still, I got out of the car and looked under, I found no oil on the ground.

Can anyone tell me WTF this is or whats making this happen?

Thanks

CHASP

Link to comment
https://www.sau.com.au/forums/topic/48879-oil-presure-problems/
Share on other sites
GTS_DUY Proficient

GTS_DUY

Posted
Posted

did you have any trouble accellerating? revs were fluctuating and dropping at all?

i had a similar problem with my engine, turned out the radiator had ran dry of water (the cap was faulty), so check your radiator and fill her up if she's dry.

this might not be the case, but have a check anyhoo

DR.ZOIDBERG Proficient

DR.ZOIDBERG

Posted
  • Author
Posted

Hey

Radiator is full

My revs are fine when driving but when I slow down they go to 0 and back to 1, sometimes it stalls, I asked my tunner and he said its something to do with my BOVs. But I havent asked my tunner about this as he is closed, so im trying to get my answer on SAU.

V8skylineMAN Grand Master

V8skylineMAN

Posted
Posted

i would get mechanical oil pressure guage, and check it against that, they are only about 50 bux from supercrap or something....im not saying put a cheap ass guage in your gt-r im saying use it to see if yours is out, or your oil pump is sha99ed.....if at all possible have them hooked up at the same time to see any discrepancies(sp?) in readout.

Idle prob:

Have you had your throttle body off at all? ever?

Also could be ilde circuit faulty making revs jump around.

AzzurrA Grand Master

AzzurrA

Posted
Posted

Or the speedo? :headspin:

I experience the same thing in my 32 GTS-t... it will sit REALLY low (not quite on 0) on the oil pressure guage, and then climb to slightly above 1/4 when driving around... i don't think i've ever see it go over 3/8th (between 1/4 and 1/2) on the guage... i'm hoping its just a faulty sender, not a shagged pump or something

INASNT Grand Master

INASNT

Posted
Posted

Dont trust the reading of the stock oil pressure gauge.

I had a similiar prob when i had my idle issues with my sard 550cc injectors. Everytime the car would go into spastic idle and go back to normal idle the oil pressure gauge used to just go to 0 and sit there and sit there for ages till i turned the car off and on again, but the oil pressure was normal while the gauge said 0 pressure everytime.

The stock gauge is also said to be very slow reacting to a proper electronic oil pressue gauge.

DR.ZOIDBERG Proficient

DR.ZOIDBERG

Posted
  • Author
Posted

Hey

I restarted the car later that night when it was just warm, and let it idle for 10-15min or so and the oil gauge sat on 2. When it was on 0 it would slowly climb when i reved it and moved a bit but then it droped back to 0, after the traffic cleared and I got going it was ok, when I came to a stop again it sat on 1 and didnt go to 0 again.

I didnt hear and werid sounds from the engine or anything.

My Revs are a diff matter I think, car idles at 1k and drives normal etc, when I slow down tho the revs dont stop at 1k again it goes all the way to 0 batt light flashers and then it comes back up to 1k again, somethimes it stalls. I am told this matter is something to do with the BOVs. Never use to happen and I was running 2 hks bovs and the stock pair (4 BOVs, Stocks sealed) I removed the stock ones as I was told it was for the best and now the revs do that. Pain in the ass it is, but thats not my may concern atm, the oil presure is and im pritty sure its the sender.

Thanks

CHASP

raz0r$harP.UK Grand Master

raz0r$harP.UK

Posted
Posted

Got the same prob too in a 32 GTST. Oil pressure drops to zero (and the red low pressure light comes on) when I come to a stop, then picks up when I start moving again. Occasionally stalled too.

But I had a few oil leaks in the steering rack, sump, etc. Mechanic fixed that up the other day and hopefully that should fix it up.

INASNT Grand Master

INASNT

Posted
Posted
Hey

I restarted the car later that night when it was just warm, and let it idle for 10-15min or so and the oil gauge sat on 2. When it was on 0 it would slowly climb when i reved it and moved a bit but then it droped back to 0, after the traffic cleared and I got going it was ok, when I came to a stop again it sat on 1 and didnt go to 0 again.

I didnt hear and werid sounds from the engine or anything.

My Revs are a diff matter I think, car idles at 1k and drives normal etc, when I slow down tho the revs dont stop at 1k again it goes all the way to 0 batt light flashers and then it comes back up to 1k again, somethimes it stalls. I am told this matter is something to do with the BOVs. Never use to happen and I was running 2 hks bovs and the stock pair (4 BOVs, Stocks sealed) I removed the stock ones as I was told it was for the best and now the revs do that. Pain in the ass it is, but thats not my may concern atm, the oil presure is and im pritty sure its the sender.

Thanks

CHASP

Who ever told you to remove the stock gtr bov's is an idiot. Put the stock gtr bov's back on as they have been used on gtr's and supras with over 500kw@wheels withput any problems.

DR.ZOIDBERG Proficient

DR.ZOIDBERG

Posted
  • Author
Posted
Who ever told you to remove the stock gtr bov's is an idiot. Put the stock gtr bov's back on as they have been used on gtr's and supras with over 500kw@wheels withput any problems.

Damn, I was told by a few ppl to remove them. Damn its always my luck and I sold them tooo :) might have to get me another pair. Will R33 or R34 GTR ones fit just incase thats all I can find??

CHASP

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Duncan
      NC MX5

      By Duncan · Posted

      Quite right, if you make it to that pension you deserve every cent
    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • MBS206
      RB20DE NEO smallbox clutch.

      By MBS206 · Posted

      From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • MBS206
      Lock up the old for sale / wtb threads.

      By MBS206 · Posted

      That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
×
×
  • Create New...