Jump to content
SAU Community

Recommended Posts

Just wondering has anyone done any dyno runs with toluene?? Just did two runs on the weekend, one with out and one with Toluene. 160 with out and 166 with the Toluene in. The mixture was only 7:1 and still got a result, just a fluke or has anyone else also had any good results?? :confused:

Link to comment
https://www.sau.com.au/forums/topic/4890-toluene/
Share on other sites

  Quote
Originally posted by U ZCREAM

Hmmm, you should be careful with that stuff. I hear it can dry out your injectors. But if you're only using a small amount for a short period, you should be fine

You are thinking of methanol (I think?). Toluene doesn't have this effect. The problem with toluene is getting a cold start when you run too high a mixture on a cold day.

MattR - It's good stuff isn't it.

:D

I've had a test on mine, no dyno time just a nice 200kms worth of driving. You will find that you can run more boost as well (within the limits of your headgasket and turbo of course). I ran a brief 14psi to test and it went fine.

With extra boost I'm sure you can get more than 166. BTW what mixture did you run?

From memory mine was 25-30%, I'd say a 10-15% would be better without a remapp unless you go extra boost.

Link to comment
https://www.sau.com.au/forums/topic/4890-toluene/#findComment-76174
Share on other sites

Gav as far as I know Toluene an Metholbenzene are diffarant according to the material safety data sheets. Toluene can be bought as a solvent or as a fuel addative, if you buy it as a solvent you pay about $50 for 20 litres if you buy it for a addative you pay about $70.

Link to comment
https://www.sau.com.au/forums/topic/4890-toluene/#findComment-76952
Share on other sites

Actually correct chemical name IS methylbenzene, (methobenzene is also commonly used but is a misnomer).

I stole 4 litres when I did my chemistry/metallurgy degree (too many years ago now) and mixed it in the fule tank of my EK Holden (202 tripple f*ck yous, a lumpy seat and exagerators).

Thems were the day me boy!

Link to comment
https://www.sau.com.au/forums/topic/4890-toluene/#findComment-77134
Share on other sites

MattR.. You run a bleed setup don't you?

You should be getting boost drop to 12 maybe 13psi up top.

Slap more boost in to it.. Maybe up to 17psi in the mid but it will drop back off to 13psi up top anyhow..

I ran my turbo like that for a while didn't damage it as far as I know.. Now with the EBC it holds 15psi all the way to redline and made 164rwkw with a untuned ecu.. So with a tuned ecu i might crack the 170 mark.. :D

Link to comment
https://www.sau.com.au/forums/topic/4890-toluene/#findComment-77251
Share on other sites

http://forums.skylinesaustralia.com/showth...25&pagenumber=1

This is an previous thread on toluene, covers most of the questions, including the myth about toluene perishing fuel hoses.

BTW I think Boostmeister had a dyno run with 30%toluene mix and got 2rwkw extra without raising the boost any (where the extra power lives)

MattR; The stock turbo shouldn't have the boost raised past 1 bar anyway, so its of little value unless you get it rebuilt with a steel wheel.

Link to comment
https://www.sau.com.au/forums/topic/4890-toluene/#findComment-77831
Share on other sites

Oh you still running stock cooler..

Maybe thats why the octane boost made such a difference as the air is hot and maybe there was really slight detonation where the ecu was pulling out timing and with the octane boost there was no more detonation..?!?

Link to comment
https://www.sau.com.au/forums/topic/4890-toluene/#findComment-78163
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • GTSboy, thank you again. i’ve been reading all the other SAU RB25 vacuum line threads and you have the utmost patience for people asking “where do my vacuum lines go”. it’s appreciated. i did also enlist a few other RB guys local to me.  i would like to run 5 to 4. turbo pressure side to wastegate actuator. i would like to run 3 to 1. power steering air valve line to intercooler outlet. (this is how it was previously). i was told 2 is the bleed port for the boost solenoid - which i’m not running - so should be capped.   anyone see any problems with that?    
    • So yes. All of them. Something like 98% of all fuel in the USA has 10% ethanol: https://afdc.energy.gov/fuels/ethanol-fuel-basics It's labelled as like, AKI, 87, 91, 93 with an E10 or E5 or E15 label on the pump. At a certain point, it's not just "E10" instead of 91. It is 91, 95, 98, and all of them have 10% Ethanol in them. You can also get E85 and E30 which is why you do see some people rolling around with E30 tunes in them.
    • Thanks for the response. This is an 04 EP3 Type R. JDM spec. Fairly certain they're just basic BC racing coils. I do plan to keep as the ride quality on stock I've been told is pretty meh given Sydney roads. If I were to go down that avenue, does NSW require them to be a certain spec (close to original) etc?
    • Should have asked what is the car?
    • I've had two super conflicting experiences with blue slips. My 30 year old E39 waltzed through with no issues but my brother in law was knocked back on 12 y/o 3 series due to wiper blades and some cracking in a control arm bush.  What kind of coil overs? Do you want to keep them after?  If it was me I'd get some dirt cheap shocks and springs from eBay or scumtree. Not ideal but will get you over the line and might even be less than $1k.
×
×
  • Create New...