Jump to content
SAU Community

Sunday 5th September, Drift Nationals Round 2 After Party :D


Recommended Posts

A huge meet up has been organised for the day after the Drift Nationals.

Where: Harold Park Paceway, Wigram Rd Glebe

When: Sunday 5th September 11AM Onwards

wigram_rd.jpg

ADMISSION FREE

Hot and Cold Food and fully licensed bar.

There will be a huge range of Nissans on hand from a KCG10 skyline all the way to R34 GTRs.

And of course, the star of the show, the R31House Drift machine!

This is also your chance to catch up, fresh from Japan, with Iwamoto-san from East Bear and Shibata-san and Sakashita-san from R31House.

The day has organised by Powerplay Imports and Fifty One Fifty, with the support of R31House and East Bear

Please register you attendance with Powerplay at http://www.powerplayimports.com/index.php?...?page=rego_form

Cool :rofl:

I just realised that I'll be in New Zealand until Saturday, so I won't be able to attend the Driftnationals :rofl:

I'll come to this and check out the cars :rofl: Will there be a video footage viewing that night too? :)



  • Similar Content

  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...