Jump to content
SAU Community

Recommended Posts

hey there, my r33 has just suddenly started misfiring @ low revs (even at stand still position)

I've just changed the spark plugs and coil packs (workshop said was fine) wat else can cuz it to misfire? I've reset the ecu after putting the plugs in and still missing @ stand still and @ low revs. Didnt go pass 3000rpm since the car was struggling. HELP!

bryanlee

Link to comment
https://www.sau.com.au/forums/topic/49267-misfire-need-help-quik/
Share on other sites

What type of Spark Plugs are in the car? And also what size gap have they been set at. I know most skylines have a miss-fire problem with plugs that are set at a gap bigger then .7 - .8.

Also make sure no vacum hoses have come off or any wires / plugs have come out of the sensors through out the motor.

Could possibly be your Crank Angel sensor if your plugs and coils check out fine, or could even be your fuel pump. What type of miss is it, a intermitent miss or happens the same all day every day ?

spark plugs - just the off the shelves one from autobarn. brand is NGK Iridium Plugs. All hoses and plugs are all in ... the missing is pretty much VERY VERY rough idling. Happens the minute i turn on the car. Drove it a few km's and it was just as horrible. Didnt go pass 3000rpm. I've had a fuel pump gone .. but there was no whining sound. Car was driving PERFECT ... this happen overnight. From perfect to @#*&!

What do i do to check my crank angel sensor and can i retune my base timing myself - w/o workshop assistance?

by any chance did u wash ur car and try to wash ur engine bay??? It happened to me once and found out that water leaked through the engine into the coil packs.. i couldnt go past 3k rpm cause it was running so rough...

It may be as simple as that?!!? Same thing with, running fine one day and then the next after i washed my car it was all fkd up..

hope that helped...

Rob..

My car did this last Friday, turned out to be a dodgy plug on the coil pack harness...you could literally put your finger on the coil-pack plug and it would run fine, take you finger off the plug and it'd run on 5 cylinders (rough)

Try that out.

Dan

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ha ha ha! I know those feels mate I've finally got the garage cleared enough that next weekend I'll do some actual work on my car (hopefully). Unfortunately garage isn't usable after 10am at the moment That said, I've done a lot of work this weekend on helping finalise a friend's Production Race car. Full started Christmas Eve. We're down to about 8 tasks on the list, including "get a wheel alignment". Sometimes it's just easier working on someone else's car or project than our own stuff 😛
    • Ha ha, ended up going it alone.  I just sent it (in a very nervous fashion).  Once I'd released the locks and it didn't automatically start spinning out of control i felt a bit more confident.   It made some loud sounds (cracking and creaking noises) when I first spun it which got the heart rate going again!  I couldn't bring myself to leave it tipped on the side.  I feel a bit more comfortable having back right side up while it sits there. I'd get angry with your last point but you're 100% correct! 😅 Even yesterday I managed to distract myself at numerous times to make a bracket to fit an LED flood light off the back of the house and fix my sons pushbike.  There were other little taks nibbling at my brain for the rest of the day too...
    • Probably one of the more nerve wracking experiences of my entire life! 😂😂 The balance (centre of gravity) is out still but in a direction that gives me comfort!   It's quite bottom heavy still meaning it takes a bit of muscle to rotate it.  The plus side of that is that it wants to to go back to upright.  Better that than wanting to go all stranded turtle on me!
    • hmmm that's not ideal. This is a pretty new engine right, will be interesting if your engine guy has any theories about causes
    • A universal ball joint removal c press kit is better money spent and will work for the Hicas ball joints.  Here's a 45$ CAD Example. ATPEAM Heavy Duty Ball Joint Press Kit with 4WD Adapters | Professional 4 in 1 Ball Joint Press Removal and Installation Tool for Cars and Trucks | Universal Ball Joint Tool with Storage Case, Ball Joint & Tie Rod Tools - Amazon Canada
×
×
  • Create New...