Jump to content
SAU Community

safc

GTRboy
 Share

Recommended Posts

Kaido_RR Grand Master

Kaido_RR

Posted
Posted
safc I for sale

blue screen model

looks like this

http://www.venus.on.arena.ne.jp/images/pri...rimera/safc.jpg

$300

pm/email

can deliver interstate at buyers expense

thanks

andrew/shibb/gtrboy

hey andrew im interested :( what does it come with? stand, book? etc?

Link to comment
https://www.sau.com.au/forums/topic/50007-safc/#findComment-995400
Share on other sites
GTRboy Proficient

GTRboy

Posted
  • Author
Posted

well its basically the same but safc has 8 more things to help tune a car finer

if youo want your car tuned for like express shit and precisness to the mm get the safc 2 or but if its just to tune it and run quite well, to the .5cm, buy the safc 1

www.apexi.com

Link to comment
https://www.sau.com.au/forums/topic/50007-safc/#findComment-995997
Share on other sites
Sydneykid Grand Master

Sydneykid

Posted
Posted

In my opinion the big advantage of the SAFC 11 is the ability to tune part throttle A/F ratios separately from full throttle A/F ratios. With earlier versions the tuner had to compromise, eg; too rich at part throttle to get full throttle OK. This affected fuel economy if you compromised rich and risked engine damage if you compromised lean. With an SAFC 11 you can have a bit of cake and eat it too. Not all the cake though, that's full ECU (as in Power FC) territory.

The SAFC1 's have great extrapolation though, so the lower number of load points is not as big a handicap as some make out.

Happy selling :P

Link to comment
https://www.sau.com.au/forums/topic/50007-safc/#findComment-997703
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • hypergear
      Blue/grey smoke after idle

      By hypergear 路 Posted

      Steam valve seals are usually responsible for cold start smoke, it goes away once engine warmed up. Disconnect it let engine breathers and let it breath freely, see if problem goes away after a short drive. Also check to make sure engine oil drain pipe is not blocked or kinked. 
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin 路 Posted

      Haha thanks! Yea I'm moving over from 2x 1000cc jets pre throttle over to 6x 190cc direct port jets and 1x 500cc pre throttle jet.  Direct port comes with all the advantages you would expect, except that pre throttle does cool down IAT'S more. That's why my direct port nozzle placement is closest to the plenum as possible in the runners to allow the air more time to cool before being sucked in. I'm also putting that one 500cc pre throttle jet to help with more cooling. It's a hybrid system. There's a lot more advantages to moving over to a PWM solenoid with a constant pressure system vs my old PWM pump setup, but I'll get more into that once I'm done converting everything over. The ricer in me is excited to see SS tubing all over my manifold though!
    • Dose Pipe Sutututu
      R32 GTST - 600KW+ RB28/CD009 Build

      By Dose Pipe Sutututu 路 Posted

      Very cool, see what I did there? 馃ゲ Wild WMI setup, first I've seen where it's on each cylinder runner, usually I see a single jet pre throttle.
    • Milkmun
      Hello fellow enthusiasts

      By Milkmun 路 Posted

      Welcome mate. What type of work were you looking at getting done? Majorly of decent skyline workshops are in the SE.
    • TheBushKangaroo
      Hello fellow enthusiasts

      By TheBushKangaroo 路 Posted

      Thanks mate, haha that's it ey, no more boosters and what not, should make for a good time
脳
脳
  • Create New...