Jump to content
SAU Community

Recommended Posts

  • 4 weeks later...

a mate of mine was pulled over and they said you cant drive a 33 on Ps. He didnt believe them so he called the cop station, or Vic Roads, or someone, and they said that its only the GTR that Ps cant drive. They removed his fine or warning or whatever, and never heard anything of it again.

.

i know that the tightness level of cops depends on the areas and their knowledge of the cars around them... but aybee.. thats really interesting, maybe the power/weight restrictions have changed since i last checked, or maybe vicroads have made a mistake somewhere?

Since R33 are imports, VicRoads may not have factory spec data for it, thus they may only refer to R32 GTR which were Australian delivered, with factory spec 206kw. Thus the power restriciton on GTR, but since R32/33/34 GTS-t were not officially imported by Nissan, they may not have that data and therefore those cars were not in their list. However doing the proper calculation based on factory spec, if all skylines were australian delivered then GTS-t could be included in the list (except perhaps R32 GTS-t, as the RB20DET factory spec has less power than RB25DET)

Since R33 are imports, VicRoads may not have factory spec data for it, thus they may only refer to R32 GTR which were Australian delivered, with factory spec 206kw. Thus the power restriciton on GTR, but since R32/33/34 GTS-t were not officially imported by Nissan, they may not have that data and therefore those cars were not in their list. However doing the proper calculation based on factory spec, if all skylines were australian delivered then GTS-t could be included in the list (except perhaps R32 GTS-t, as the RB20DET factory spec has less power than RB25DET)

that could be possible but it seems unlikely that the cops wouldnt be into this by now.

What im trying to understand is why they use power figures from the factory (at the flywheel) and not at the wheels? I understand that getting these kind of figures would be a problem but it seems like an inaccurate measure of the cars true power

you're thinking is right, power figure at the wheels is not as accurate as factory spec claim (although we know that Nissan may have 'detune' factory spec claim on GTR to make it look like didn't exceed 206kw gentlemen's agreement).

There's so many factor on dyno that can affect power at wheels, tyre size, ambient temp, worn clutches, etc. Each car even from the same make and model can show different figure on dyno, especially 2nd hand ones, and testing each car out there for every P-plater would be uneconomical, so just use the factory spec figure and calculate from there what is allowed/not allowed.

If you keep getting pulled over my advice to you is log it (write it all down) and make a complaint. I"m not sure who does police complaints in victoria.

I remember one of my friends bought a car from a drug dealer - he used to get pulled over by d's, undercover, highway, local - every cop car. After he found out who the car belonged to and complained to his dad (some richy rich conections guy) who made a complaint to the police and ombudsman (or whoever) and he never got pulled over again.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you put an aftermarket oil pressure gauge on and verified your oil pressure?   Noise being on the block, on exhaust side, how high up the block does it seem to be? It could be the VCT system getting cranky, especially if it's mainly at idle, and when warm, as that'll be your lowest point for oil pressure. Could be showing that oil passages / VCT solenoid are blocking.
    • Well, hydraulic lifters will get noisy if they are dirty/fouled in some way, and exactly how that manifests will depend on exactly what schmutz is where. There is a procedure on here somewhere for dismantling and soaking/cleaning them. Replacing them with new is about 50% of the work and about 5% of the money!
    • Thanks for the reply @GTSBoy this is is a hydraulic lifter engine. Yea right i did not realise the lifters were supposed to be compressible while installed. I could push them down but i had to lean almost my while body weight on them.  I have never heard of a lifter/ lifters ticking only at hot idle and getting worse the hotter it gets. I have owned a few jdm cars with noisy lifters. This noise is slightly more subtle, it is more of a sharp gentle metalic tic than the solid and more loud tapping I've heard on lifters. I have used a metal rod, alloy tube, hose and stethoscope and could not find the source of the tick. But it appears to be loudest on the actual engine block behind the exhaust cam gear and next to the oil filter. I had mate (40 year old mechanic) go over it with me and he couldn't find it either..  Could it be a cam seal issue of some sort?  Cheers  
    • This seems problematic and unlikely at the same time. Vanilla RB2Xs have hydraulic lifters. They do have "zero" clearance, but only when running with oil pressure inside them. When not running, you should be able to compress them and obtain heaps of clearance. RB26s and Neos have solid lifters. They should have ~0.3mm and ~0.5mm on the inlet and exhaust respectively. If they have zero clearance then bad things are happening. With nothing else being wrong, it would mean that the valves would be held slightly (ever so slightly) open when they are supposed to be closed and it should have all sorts of problems when running, caused by leakage in/out through the valves. Or, zero clearance can indicate severe valve seat recession. None of it is good. Have you used a piece of hose as a stethoscope to try to localise the noise?  
×
×
  • Create New...