HKS GT-SS's installed!

[markr34gtr]

At least a bleed valve would hold boost steady

I'm using a Turbosmart eBoost, in case anyone can offer any solutions or suggestions...

you could give your actuator rods a few mm more preload it will help hold higher boost levels... thats what i needed to do to hold 30psi steady, my base boost is now 14 psi with zero setting on my id3 blitz controller...

well done with those power levels so far...

hope this helps....cheers...

[Roy]

....More than enough for track work IMHO.

Now it's time to attack the car with weight reduction

:werd: ... As long as you are still making good power up top, i seriously doubt even guys with 400+rwkws will be able to match you coming out of a corner and have enough of a straight to catch and overtake between corners.

Yeh now you need to rip off the HICAS, throw in some Kevlar seats and goa rac'n :headspin:

[INASNT]

At least a bleed valve would hold boost steady

I'm using a Turbosmart eBoost, in case anyone can offer any solutions or suggestions...

Have you tried a hks evc 3 or 4?

[600hp]

great results merli thats what we expect as well.

when does the boost start,and could you post a copy of your dyno graph,as i think everyone would like to cheack it out. how many kays did you put on it before the tune and who was it that did the tune if you don't mind?

dough boy do you think it could be the exhaust housing that could be causing the boost struggle.

another thing was that on the HKS web site they state that the SS's are ment to flow as much as the 2530,320hp each i think.

i don't know how true that maybe ,but i've also seen a HKS dyno graph the a set of SS's on a 2.8L and 274deg camed car pull 750HP at the engine!

has anyone SEEN! big figures from GTSS's.

Merli again great result

by the was we are using a blitz i-D boost controller if that means anything,seems good but it hasn't seen any boost yet so hard to tell.

[yamaha227]

merli, i had a turbo smart e-boost put on my gtr last week and its working really well, turbo's are spooling faster as its helps hold the wastegates shut for longer. make sure your gate pressures are set right, they tend to spike and fluctuate a bit if set to sensitive and make sure your over boost shut down is set atleast .2 bar over your max setting... see how that goes

[MELV]

Can someone post up a dyno graph..... Merli ?

[meggala]

merli cmgrats man sounds like a great power curve perfect for the track and perfect for a gtr.

enjoy

meggala

[Penfold]

Did you guys just get the GT-SS kit? Wheres the best place to get it from & do you need any additional gaskets, actuators, etc?

Cheers,

Penfold

[MELV]

i belive nengun sell the complete kit with everything u will need

[600hp]

I bought ours of Dough boy but i'm not sure if he will get anything more from japan otherwise i would have got them of nengun!

the kit comes with 2xturbos 1xexhaust gasket and the little hoses that you need and it shows how to install them as well.

i was just at supernats and saw joe but his RX-7 into the wall not a pretty site but he's OK.

his car is stuffed.

[600hp]

I just heard through the grape vine that merli/andrews R33 GTR which just made 300awkw just died at the race track, i heard that it threw a main bearing. or something i hope this isn't true as i couldn't think of a better drag, than a r33 gtr with the same turbos and the same cams.

Andrew can you tell us, what happened?

[Shibby]

Did someone say B-man???

[MrNismo]

600hp you might be interested at mine:

http://gtr9995.com/pictures/powergraph_4wheel.jpg

Setup is pretty much like yours. Just that i'm running on 264 cams and 680cc injectors.

[600hp]

nice one anyone else got some dyno graphs of gt-ss's

thanks mr nismo

[B-Man]

Did someone say B-man???

I sure hope not

[CalaisT3RBO]

600hp how far have you got so far with your car? I am about a month behind you with a similar setup.