Jump to content
SAU Community

Recommended Posts

  • Replies 90
  • Created
  • Last Reply

Top Posters In This Topic

I'm a bit confused, you guys are talking about the FC Datalogit made here in New Zealand, but what is that software I downloaded? It's from japan obviously, is it for tuning the power fc ie, the actual legandary software for Power FC that everyone always talks about but only the japanese have????

Dave

there's two types of cable adapters you can use. a standard one, and a extended one, which allows you to hook up a wideband O2 sensor etc.

I've made up an extended adapter and have a PCB made up n all for it. However to use the homebrand adapter on your PFC you need to replace the NEC I/O controller chip in the PFC with a blank one which has a cracked firmware on it. This is where I'm stuck because I can't for the life of me get my hands on the NEC programmer (I can get the blanks but not the programmer). This is deomnstrated in this pic... http://www.skylinesaustralia.com/forums/at...achmentid=22279

this is the standard version of the interface

http://www.skylinesaustralia.com/forums/at...achmentid=22278

this is the extended version

http://www.skylinesaustralia.com/forums/at...achmentid=22277

which has extra input ports.

The rest that you've pictured are prototypes. Hope that helps you guys a lil.

we're talking about the Power FC Communication software that is used by Power Excel tuners to tune PFCs. Not the Datalogit. The PFC communication software's been on the market (if you knew where to look n who to ask) for about a year now.

basically if you wanna tune your own power fc this is what you do...

a) get power fc

B) open it up

c) desolder the NEC I/O chip from the main board

d) get a blank version of that chip

e) get an NEC programmer for that chip

f) put a cracked firmware on the chip

g) solder the chip back on, or better yet, get a quick snap socket for the chip

h) plug the ECU back in and pray that it works and you haven't flushed $1000 of PFC goodness

i) make yourself the home-brand adapter (standard or extended)

j) install the communication software that corresponds to your PFC

k) do a serial connection and tweak away

simple enough? :D

because the power FC isn't meant to work with homemade circuit boards. it has a CRC checksum I think that it applies to the I/O to see if the data is being sent thru a proper Apexi supplied data cable. Which makes sense. But that's what I think anyways :D

Is it not easier to reverse engineer the datalogit so you can solve that problem without opening up the power fc and have datalogging capabilities?

I'm not electronics engineer, but if datalogit can do it, surely we can too by looking at someone's datalogit.

Dave

I am quite certain you do not need to de-solder anything in order to use that software to tune the Power FC

http://www.skylinesaustralia.com/forums/sh...97&page=1&pp=25

When that Jimmy guy tuned my car with the same software, I do not remember him removing any chips at all. He just plugged the box into his laptop and to the Power FC.

Jimmy is an authorised excel dealer in Taiwan and hence has the correct Power FC cable/box.

What funkymonkey is saying is that if you don鈥檛 have the legit cable/box then you have to figure out a way of inputting/outputting data past the protection chip inside the Power FC.

i'm sure it can be hacked.. even if you have to hack the software itself.. they cant have spent that much on the protection... and even so its only circa early 2000's protection which was always cracked.

If Maya and 3d studio and the rest retailing for $10k or so .. have been dongle hacked, so can PFC ..

now do we have any russian crackers in the house?? hmm ..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Car looks clean as. You ended up getting quite a bit done 馃槀  So what's the plan for the exhaust? 
    • The only Neo rods that were any different to any other RB25 rods were the DET ones, and they were the same as RB26. Here is a Neo DET rod. O5U part number visible. Here is a post in a thread here on SAU with evidence from someone who has done this before. There are photos in the thread of normal RB25 rods.  
    • Sure, but why assume that will be the case forever? And why assume you'll be able to do an oil change to swap back to a stock drain bolt before that happens? And does it even matter when I change the oil at fairly short intervals? Life can be funny sometimes and unexpected things can happen. Like breaking a collarbone so you can't do any work on your car for a few months but the oil change is due so you have to take it to somewhere and hope they don't do something stupid like stacking the new drain plug washer on top of the old one.
    • Do u know how to identify the rods are rb25 or neo ones? Can u look into the pics and tell me is they de or de neo ones. Its confusing becoz my motor has de neo head but block is 25de 75t, so really confusing me about rods, crank.
    • Are you talking about the oil squirters? There is only one place for them to go. Yes, you have to drill the holes. Yes you have to obtain the correct oil squirters (I presume there is some sort of aftermarket option available, because original turbo ones are going to be a diminishing resource).
  • Create New...