Jump to content
SAU Community

Recommended Posts

took the car for a spin yesterday, just for the hell of it, before taking it to the electrican, had a mate in the car so i dumped it and its started to spin the passenger side wheel then knocked it into second still spinning but changed to the drivers side wheel spinning?? i'll put up a pic of the black lines as its even funny to look at.. anyone know while this would happen???

Cheers Matt.... dam it was good to drive her again...

Link to comment
https://www.sau.com.au/forums/topic/51368-i-think-my-diff-is-broken/
Share on other sites

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

its been sitting a while, right?

flog it a bit then change the oil...the plates are prolly seized and have only let go on one side....it should free up... but if it doesnt....u need a rebuild.

also another thing is that when i have the car off the ground and spin the wheels by hand one will spin one way and the other will spin the other?? the cars at the auto electrican at the moment which is across the road from my machanics which is were the car is going next, swapping over the rear calipars and hand brake set up so i'll get him to change the diff oil to one of the ones above then too. thanks for ya help

Same brands as any oil you would use in a open wheeler diff....just that they formulate it specifically(sp?) for lsd's

Same deal as engine oils....different formulas and viscosities for different applications.

Open wheeling diffs will spin the other side wheel the other way when car is jacked up.....clutch pack type(plate) Lsd's will do the same just a little bit until the lsd unit kicks in(which is like 1/10th of a turn- not much) if the plates are not working properly like in RSX84's case, it will operate exactly like an open wheeler. because the slip is not limited.....this is assuming that his is a clutch type Lsd.

If it is viscous, then im unsure how it works but my understanding is the the oil in the viscous unit is forced thru little valves in the unit thereby causing both wheels to turn because the oil does not freely flow.......so i dont know how it would act in a jacked up situation because you wont be able to exert enough force by hand to make it work correctly.....

I know what I meant but I dont know if I have made it clear...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The trigger kit I have is similar to the one in the link below. While going through Facebook, I saw someone else mention a similar issue, and I’m starting to think this could be related to the crank gear itself. I understand these parts are CNC machined, but maybe some earlier versions or individual pieces might have slight inconsistencies—it just doesn’t look right in my case. https://www.facebook.com/share/16an8evZd9/?mibextid=wwXIfr I originally installed the crank gear using the thin OEM washer, but as shown in the attached photo, the timing belt walks very close to the edge. When I tried using a Nitto washer—which is thicker—it actually made the issue worse. The belt walks about 1mm off the front edge, which raises more concern about alignment.   I’ve gone through the full process of elimination:   The tensioner pulley and bolt are brand new and installed correctly. The bolt isn’t bent and is oriented properly. The back of the tensioner and the idler pulley are clean and seated correctly. The idler sits slightly more forward, which I understand is due to its design. I’ve experimented with both tight and loose belt tension, but it makes no difference. As soon as the engine runs, the belt immediately walks forward again—even if I reset it beforehand.     At this point, I’m considering replacing the crank gear with your Race Version 1 (12-tooth), but before purchasing, I wanted to ask:   Are you aware of any alignment issues when using this gear? Would this gear help keep the belt aligned correctly, or could the walking still occur? Does it work with a standard missing-tooth crank and rear washer? Is there any specific crank setup or install procedure required?     For reference, I’m not using a front washer, as the PRP crank gear seems to replace the need for one.   Looking forward to your advice.
    • Yep, looks that way. Never driven an E30 or R31 so I can only imagine  
    • Yuh, My new R34 box is sitting on the workshop floor (in its large shipping box, which is a nice thing on its own), along with a front plate to convert to push clutch. There was no way I was interested in rebuilding my existing one. Was only partly interested in the risk of buying a used one. But, if you want a 2nd hander, I can point you to one in/near Melbourne at least. @Komdotkom has one that should be in good enough condition to be usable. I don't think it's in a for sale thread, you'd have to message him. @redzedhas one that definitely needs a rebuild.
    • I used to love going to Amaroo to watch the HQ series go for broke (eventually stopped due to lack of spare parts) and also the Porsche series.  It was so cool to back your car up to nearly the edge of the viewing barrier and party with your friends, having a bbq and alcoholic/non drinks. It was such a family/mates atmosphere
×
×
  • Create New...