Jump to content
SAU Community

Recommended Posts

Just to let everyone know there is going to be a phone poll on Channel 9 news tonight about the new amendments to the laws. I encourage everyone to phone up in the negative and get many others to do it. It might not mean much but it is a voice.

I, in the meantime am trying to get someone in news to put an alternate view of the story up.

Link to comment
https://www.sau.com.au/forums/topic/51529-anti-hoon-laws-phone-poll/
Share on other sites

Phone Polls are revenue raising just like anti-hoon laws :cheers: but at least there is a good reason to vote in it.

Have you got a number to call? I'll try to if I get home in time (mobile flat) or is it being done all tonight/tomorrow for the results to be on Tuesday night?

Being done tonight. 10/09/04 Results tommorrow.

The number will go to air at 6:05 tonight. You have around 24 hrs to vote.

As I said it might not mean much but it does show the 130,000 or so people who will be watching that there is opposition to this spurious law

only 2100 calls total thats f*** all

nah you've got heavily biased people that will say that 60% against the law is too close to 50% so the 40% of wankers voting for will be shown as having the overwhelming support.

No hijacking a person's number doesn't cost me money at all.

i've **um** seen it before done with dialer trojans latched onto someone's computer that does winfax through the dialup modem.

Basically since the trojan just keeps dialing a number through the modem.

The winfax program that came with win98se allows the modem to be used as well to call people aswell as fax.

Don't think its possible to do it through broadband because of the digital signal and the net doesn't access the analog signal.

Hmm must find out if Michelle uses dialup at home cause won't it be funny that the voting poll is like 10000000 against to 900 and she gets racked for a $million dollar phone bill

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Does your rb gearbox have the common input shaft bearing sound? (One one where it goes away when u push the clutch in or get to higher revs) I heard if you put the wrong oil it can get this sound.
    • There's more than one way to skin that cat, and most of the sump Maatouks have done will be GTR sumps. They are HUGE in GTR drag racing here.
    • Yeah...I always start at the shift solenoids, because there's only a few reasons these will spook into limp mode, and bad shift solenoids is one ~ the other can be the shift control module (if you have steering wheel shift buttons)...it's easier to eliminate the solenoids first.
    • Might piggy back off this thread since there's been a good discussion about PWM.   I purchased a Walbro 460 F90000267 and have been looking into PWM to understand it. It was purchased more of a future proof as my original OEM fuel pump died (r33 below 200kw) and figured I'd just upgrade it to this. That's when it hit me that a pump this big can cause more dramas with such high amperage draw and heating of the fuel pump being on 100% all the time in such a mild setup.   I have a Nexus R3 and slowly collecting power mods but I was looking into the PWM feature on the NSP software:   Then looking at the graph from the fuel pump:     Am I safe to assume reducing duty cycle to 50% for example would make the pump run like a 230/lph ? Where does the PWM come in all of this ?   I've gone down the rabbit hole of PWM fuel pumps and it seems there are many differing opinions on how to go about it 😅  
    • Thank you, this will keep me busy for a bit.  I will update progression.
×
×
  • Create New...