Jump to content
SAU Community

Recommended Posts

Sorry mate, allow me to explain.

You car has been tuned for a re-circulating BOV. When you have a BOV that vents to the atmosphere (opposite to your stock one) your car will run rich when you change gears and your exhaust/gases are hot enough to ignite the extra fuel that is not being used, hence the reason you will get a pop or explosion in your exhaust. There are two causes of this.

1. A BOV that is tighter than the stock one will usually makes the turbo flutter, which is called reversion. Reversion is where air bounces off the butterfly (throttle body) back through your piping and out of your airfilter past your AFM (Air flow meter) which cools the sensor and therefore making your fuel mixtures rich. This happens as the BOV is too tight to allow small boost pressures to make it open.

The other is

2. When the BOV opens to the atmosphere the ECU has already recorded this air passing through the AFM and thinks the engine has used this air when really it hasnt there for the fuel for this air has been added to the mixture but the air has escaped = rich condition.

A SAFC is a Super Air Flow Converter made by APEXi which taps into your AFM which enables you to alter the fuel maps at different RPM/Load levels.

Fouling your plugs means your spark plugs are coated with unburnt fuel and carbon which makes it harder to get a clean ignition spark.

Hopw that helps,

Ben

This my seem like a silly question, but.........

I'm getting pops when i'm using the engine for braking, and I *know* it's running rich, as it's currently using a mines ECU.

(It's popping, mabee once or twice in 20-50km's of driving with roundabouts etc)

I'm seriously looking at changing to a PFC asap, with the retune - will it get rid of the pops etc?

TIA - Zeb

i have a SAFC and an atmosphere BOV and i still get the pop, it happens quite often, but i think its kind of cool. I also have a gutted cat, so when the air is cold and its dark you can see about a 30 burst of flame every now and then.... if it doesnt do any damage to the engine, i cant see any reason to change it

ummm when i had my stock BOV on, i actually had the "pop" sound from the exhaust occasionally, like not all the time. ONly when i rev harder, there would be the occasional pop. What does that mean? since i wasnt using a atmo bov

It just means that your exhaust is hot enough to burn the unburnt fuel.

My old car was a 1990 Honda Integra (non vtec) but with cams, exhaust, etc...(no bodykit, just lowered with big sticky rubber). It popped and crackled louder than any car I've ever driven. I owned that car for 7 years, drove it every day and not once did I get pulled over by the cops because it was popping and crakling on the overrun. I did get pulled over once for doing 70+km/h WOT around a really tight corner though. I was let off with a warning. The policeman said he heard me coming.

no defect.

If you drive stupid, and act like a smartarse you'll get done. Drive normally, and treat cops with respect and you'll be fine.

RE: "...will the pop sound come out with flame?"

If you get rid of your catalytic converter or gut it you'll get flames. The fine for having no cat though is $10,000 last I heard.

wil..

  • 1 year later...

In my R33 series II '97, I have a 'Stealth' BOV from Go Fast Bits which has a plumb-back as well as a trumpet outlet, it has two type of settings, spring tension and outlet, it allows you to set the ratio between full dump to the plumb-back or trumpet and everything in between, so what I did was started with full trumpet and gradually tried settings (all 17 of them) until the 'pop' or backfire goes away, by doing this, you are allowing just enough air back into the inlet to stop the 'running rich' condition. Believe me, I paid AUS$550 for the Stealth with the extension trumpet and it's worth every cent ! ALSO, I got pulled over once and this cop tried to defect me for my BOV and I jarded him by turning it off !! now, how many BOV are there that lets you turn the sound off right there n then without having to pull the damn thing off?? I think Go Fast Bits now have a new version that just came out not that long ago that has a electric servo built into the BOV so that you can make the setting from inside the cockpit. Now Try that sucker !

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, pretty much what you said is a good summary. The aftermarket thing just attached to the rim, then has two lines out to valve stems, one to inner wheel, one to outer wheel. Some of the systems even start to air up as you head towards highway speed. IE, you're in the logging tracks, then as speeds increase it knows you're on tarmac and airs up so the driver doesn't even have to remember. I bet the ones that need driver intervention to air up end up seeing a lot more tyre wear from "forest pressures" in use on the highway!
    • Yes, but you need to do these type certifications for tuning parts. That is the absurd part here. Meaning tuning parts are very costly (generally speaking) as well as the technical test documentation for say a turbo swap with more power. It just makes modifying everything crazy expensive and complicated. That bracket has been lost in translation many years ago I assume, it was not there.
    • Hahaha, yeah.... not what you'd call a tamper-proof design.... but yes, with the truck setup, the lines are always connected, but typically they sit just inside the plane of the rear metal mudguards, so if you clear the guards you clear the lines as well. Not rogue 4WD tracks with tree branches and bushes everywhere, ready to hook-up an air hose. You can do it externally like a mod, but dedicated setups air-pressurize the undriven hubs, and on driven axles you can do the same thing, or pressurize the axles (lots of designs out there for this idea)... https://www.trtaustralia.com.au/traction-air-cti-system/  for example.... ..the trouble I've got here... wrt the bimmer ad... is the last bit...they don't want to show it spinning, do they.... give all the illusion that things are moving...but no...and what the hell tyre profile is that?...25??? ...far kernel, rims would be dead inside 10klms on most roads around here.... 😃
    • You're just describing how type certification works. Personally I would be shocked to discover that catalytic converter is not in the stock mounting position. Is there a bracket on the transfer case holding the catalytic converter and front pipe together? If so, it should be in stock position. 
    • You talking about the ones in the photo above? I guess that could make sense. Fixed (but flexible) line from the point up above down to the hubcap thingo, with a rotating air seal thingo. Then fixed (but also still likely flexible) line from the "other side" of the transfer in the hub cap thingo up to the valve stem on the rim. A horrible cludge, but something that could be done. I'd bet on the Unimog version being fed through from the back, as part of the axle assembly, without the need for the vulnerable lines out to the sides. It's amazing what you can do when you have an idea that is not quite impossible. Nearly impossible, but not quite.
×
×
  • Create New...