Jump to content
SAU Community

Recommended Posts

I lived in Boston last year and saw those Impalas everywhere. They certainly have the R34 lights going on at the back there.

When I told people I drove a Skyline they either had no idea what it was or were totally in awe. When asked about it (by the knowledgeable ones), I'd just say it was an R33 Skyline and most of them assumed it was a GTR. Of course, I kept quiet about the fact that it wasn't :P

once i met some guys that were from the us only here for a few days, when they found out i drove a skyline they were like omg as if its a ferrari or some mythical car lol.

i took them for a drive in it, and told them to sit inside and take a pic to show their friends, the were like nah nah as if its too much of an honour! lol!!!!

Hello from Sydney now. :rofl:

I was in cali when I posted. But I've been to Florida, Chicago and also Wisconsin.

When I tell people I have a gtr they worship your every word. Strange cause I think it's just a car..... like any other... :confused:

It was an interesting trip I . I tried all this american food and it's a good change from all the regular. Eg, who had steak and eggs on the same plate? Crousant, sausage, egg and cheese in one... getting strange now.... but I notice that they called what we deem "chilli" as "pepper".

Wendy's is a restraunt, not just an ice cream shop.

But yeah, still have to explore the place a little bit more in future.

I think that's what I like about over there. Something is ALWAYS open. Denny's, IHOP just to name two. It's better than just kebabs and i your lucky, maccas.

But just to pick a bone, at Wendy's. I had something called "Chilli's". Here I am expecting this thing to be all chilli/hot/spicy, and there's absolutely NOTHING when I stuck it in my mouth. "HELLO! ANY DAY NOW!". It's just mince beef and tomato, etc.. mix. Taste good but no chilli. I was disappointed with that.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It's definitely not firing order. But I think it should also be made clear that the output that gets fired is the one that corresponds to the input that was switched at the ECU. So you could scramble them up totally so that the numbers meant nothing, and so long as you had the inputs and outputs matched up, you'd be fine. The reason I make that point is that blanket statements about what it is supposed to be don't always hold out in a world where there's been 30 years for the wiring to have been stuffed with.
    • Hello, im asking about this guy - coil igniter on rb25det series 1 r33 s1 engine. I need to know if pins on coil side indicate coils itself from 1-6 or it’s firing order so pin nr1 goes to 1st fired spark plug:(1pin-1firing spark, 2pin-5order firing spark, 3-3, 4-6, 5-2, 6-4…)   photo: https://files.fm/f/k9pdug38uq
    • Remove it. Certainly from the hub face. I'm not in love with leaving it on the wheel assembly surface either - but if it is common to do so, then....maybe fair enough. It's not difficult. Just time consuming. For the hub face you just need a large enough block and suitable grades of abrasive paper to get it off flat. The same would be true of the assembly face. Just more time consuming, probably needing a lot more care. It's defo going to be easier just to assemble the wheels as is, seal them up, and check them periodically to see if there's any movement or loosening of the fasteners, than it will be to remove it though.
    • Hello, I got my wheels powder coated and they've powder coated bloody everything the mating surface and hub (even told them not to lol) anyway should I leave it or remove it. (Would be very hard) I've searched a lot and lots of powder coaters don't mask the mating surface but do mask the hub surface. How bad it powder coat on the mating surface or hub? My question is what should I do?
    • Yeah, R34 with RB25DE likely has a 4AX01 box in it, which is a medium duty auto ~ with the RB25DET mill, it would've been fitted with 4AX00 (4AX13) heavy duty build (same case, different internals). An RB25DET will lunch on a medium duty 4R01 auto in pretty short order ...to give you some visual idea of differences between the 'medium' and 'heavy duty' boxes, you only have to look at the 2/4 band for comparison...it's chalk and cheese...(plus bigger high clutch, extra pinion in the planetary sets, higher oil pump output, different bearings, higher TC stall speed )... You can control them with just about any aftermarket TCU for electric-over 4-speed with TC lockup clutch (ie; the GM 4L60E and others)...I have a custom standalone TCU that includes MAP sensor (for turbo applications) along with TPS, RPM, and line pressure monitoring...in other words, I don't use any ECU signals...no real need to.
×
×
  • Create New...