Jump to content
SAU Community

Recommended Posts

  • Replies 204
  • Created
  • Last Reply

Top Posters In This Topic

Put mine in this morning,

But the speedo catches at about 40 and 60,

and the tacho catches at about 4000 rpm and wont go higher.

I have it all pulled apart agin now?

any suggestions?

I might use some hot glue to hold it down a bit better round the edges.

Hi guys, just installed mine, and works awesome!!! Here are a few little tips and tricks I did along the way:

Fed most of my wires through that gap on the RHS of the instrument cluster next to the taco. Saves taking connectors off and putting them back on...

http://www.skylinesaustralia.com/forums/at...achmentid=24826

Cut the wire for the EL Speedo, fuel and temp and fed the wire through the gap on the Top LH corner where the black wire on the back sits, then soldered the connector back on.

http://www.skylinesaustralia.com/forums/at...achmentid=24827

Rule number one!!! BE PATIENT and careful when installing the EL dials over the current dials, the Speedo/fuel/temp is the hardest one to do.... I found it was best to point the needles all at around an angle of 60 degrees

For wiring the power to the controller box, i tapped into my negative wire for my turbo timer... For postive, I ran it straight to the cigarette lighter. BE SURE TO TAP INTO THE SMALL CONNECTOR for positive

http://www.skylinesaustralia.com/forums/at...tid=24831&stc=1

I stuck my controller box next to my fuse board using double sided tape, makes things neater...

http://www.skylinesaustralia.com/forums/at...achmentid=24829

As someone else stated on here, you can select the colour you want, and then unplug the controller and leave it somewhere else. The controller is too ugly for my liking so I actually left the controller wire hanging out of the fuse board cover, sits nicely and you can plug up anytime and is sought of in a secret hideaway position...

http://www.skylinesaustralia.com/forums/at...achmentid=24828

And the finished product:

http://www.skylinesaustralia.com/forums/at...tid=24830&stc=1

Shit while doing it i snapped the clear plastic infront of the speedo and tacho and that, anyone know where i can get another one quick!!

Also how do i get to the boost guage? do i have to unsrew the tacho from the back?

Ok I fixed it,  

I used a pair of scissors to GENTLY pry the needle out a bit so it clears the dial

No I didn't,

It seems there is a bit of "play" in the tacho needle.

If I pull gently on it , it comes out and clears the dial. after awhile it must vibrate back in and is now catching around 5000rpm.

and ideas friends?

No I didn't,

It seems there is a bit of "play" in the tacho needle.

If I pull gently on it , it comes out and clears the dial. after awhile it must vibrate back in and is now catching around 5000rpm.

and ideas friends?

Yeah just took mine for a spin and it does the same starts catching at about 3/3.5 and keeps stuterering as im accelerating, maybne the screws in the back of the tacho may have something to do with it but im not sure anyone got any other ideas??

Yeah just took mine for a spin and it does the same starts catching at about 3/3.5 and keeps stuterering as im accelerating, maybne the screws in the back of the tacho may have something to do with it but im not sure anyone got any other ideas??

I found mine was catching on the TACO round 5000rpm and jutters all the way to 6.5-7k, then jutters back as I let off the accelerator...

Pulled the dash out again and wiggled the taco needle up abit and spun it a fair few times and tried pushing down the EL dial more...

Seems to have worked :(

Theres are good but after about a year of heavy use you will find the inverter will start to play up and the backlight will start to flciker while driver with the lights on and if you have other things on like the a/c, rear demister, or wipers.

If you guys installed them yourselfs i bet you speedo and tachs are around 200-300rpm out.

inasnt so wat exactly are youy trying to say?....

i think i should get someone to install them

since everyone is startin to have problems with installin them

Pay extra and get someone that knows what they are doing to install em, coz once you *** the springs on the speedo and tach even a little the speedo and tach will always read wrong. My oil pressure gauge sometimes decide to read 0 when there is full oil pressure since i did my conversion

I just put mine in and put some glue on EL tacho towards the bum of the needle and it aint catching, hopefully it doesnt, nut it is reading 150-200 rpm out when measured against my avcr, but they look awesome, i know motorware won install them on sklyines because they dont like to as its risky breaking the needle and other place are charging over $100

  • 1 month later...

For the guys who were having problems with the needles getting stuck, has anyone got any good suggestions as to how to stop this from happening?

Glue has been mentioned, but I don't know whether it will be visible when they're lit.

Any suggestions would be appreciated.

For the guys who were having problems with the needles getting stuck, has anyone got any good suggestions as to how to stop this from happening?

Glue has been mentioned, but I don't know whether it will be visible when they're lit.

Any suggestions would be appreciated.

What I did was give my needles a good wiggle, well a hard one at that... Mine were originally catching(TACHO), but dont catch no more.

Not the most recommended of ways, but it worked for me and have had no problems since

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Dunno what to tell you, when I look at it on Consult I can see this warmup timing map kicking in around 40C coolant temp and it sticks around for a while:  At part throttle on the normal base timing map it peaks around ~43 degrees of timing or something like that, this warmup timing map drops it to like 12-15 degrees. 
    • I don't think that's what you're seeing. Something else doing that. The only time I've seen it get so retarded is when it's trying to control idle (in which case we're not talking about mapped timing tagets anyway) and when there is an extreme coolant temperature sensor fault. The RB26 ECU is essentially the same as the 20 ECU and I knew that ging inside out. There is no facility for it to retard that heavily on cold start. The OEMs never used to do it back then. I mean, shit, the catalyst is abotu 3 miles down the exhaust anyway. Early light-off was just a twinkle in some EPA arsehole's eye back then, not a regular engine control strategy.
    • I must preface my comments with a general expression of ignorance. I have no specific knowledge of these NA automtaic things. I can only assume that the "steering wheel button" is for enabling the tiptronic controls. Wierd that it would even need/want a button for that... But anyway.... Was the car previously tiptronic? Did you put a new cluster in as part of all this?
    • Regardless, it doesn't seem wise especially on RBs to actually chase MBT. Timing scatter is the big one on stock CAS, even if that's fixed overshoot is worse than undershoot. 
    • It's all about reducing the overall output. Reduce the source of it, you have wayyyy less to deal with in every other step and trick you play with. It's why something like a modern vehicle, so VW, Audi etc, there's thousands of tables for the ECU to calculate what it should be doing with the engine.   Why would you NOT reduce emissions the most effective way possible, when it has very minimal tradeoff, AND manufacturers are always struggling to meet the current standards.
×
×
  • Create New...