Jump to content
SAU Community

Recommended Posts

Hi Guys i got a problem with my car reving past 4-5 rpms... it starts to splatter... sounds like the pistons is goin to blow out of the block...

R33

RB25 DET

slight mods

- airfilter

- 3 inch all the way

- 9 - 10 psi.

only started not too long after i installed a FMIC.

also my fuel lid isn't pressurized. the seal is cracked would this do anything?

also just had a full 80K service.. all new iridium sparks still not sure why its doin this...

Link to comment
https://www.sau.com.au/forums/topic/52257-high-rpm-problem/
Share on other sites

- Even one cracked coil can cause a lot of hesitation!

- i was getting it between 4500 - 5500 rpm, and after that it was all good, it would rev out nicely...

- When i taped mine the problem went away, but after a week or two, came back b/c the tape shrunk on the coils, exposing parts of the crack once again

- I would be doing this to ALL of the coils, regardless of wheather there is a crack there or not, as it could crack soon anyhow as the others have....

umm... this sounds like wats happening exactly..... (4500 - 5500 rpm) but just a question wat is hesitation? its not like back fire is it? not poping from exhaust right?

Link to comment
https://www.sau.com.au/forums/topic/52257-high-rpm-problem/#findComment-1032433
Share on other sites

Yeah, that's what I was implying with that post. It pops, and misfires at around that point at WOT.

Even if you fix your coils, at higher boost, best case scenario is that instead of popping and misfire, you will get a flat spot at around that point.

You will need a new ECU, or a SAFC to retune your air to fuel ratios, as they get VERY rich at around that point with higher boost. I think that timing gets retarded too b/c of the overfuelling, hence the massive flat spot / misfire.

Even with a SAFC, b/c it runs leaner after a tune, the timing does not suffer as much. I only have a SAFC, and I have NO flatspot. In fact, where the flat spot used to be, there is actually a tiny surge or power.

Below is a pic of my dyno graph before and after the SAFC. (Note on the first run - green, my tuner backed off b/c the A/F ratios went crazy. Then sensor he was using to measure the A/F ratios was buggered and he replaced it after a couple of runs.)

Link to comment
https://www.sau.com.au/forums/topic/52257-high-rpm-problem/#findComment-1032816
Share on other sites

Hey Zahos

I am running 12psi and have an SAFC2. It been running great for months. Then on the weekend the car developed the same misfire you guys are talking about. popopop at around 5000rpm and a short drop in power. When I dropped the boost to 10 psi, the problem went away. The spark plugs should be fine as they are new. Would this be a sign the coil packs are on there way out?

Link to comment
https://www.sau.com.au/forums/topic/52257-high-rpm-problem/#findComment-1041688
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Last year I got a set of MCA street coilovers for my turbo Forester after my son hitting a concrete gutter/wall on a small bridge causing the whole drivers side suspension to get bent because the rain just made the car slide out I love them, I think they were $2400. even had a hiccup of have the wrong hub configuration (my fault) so got onto MCA and they sent the correct shock ends overnight parts from QLD, for free!  I was very impressed with their customer service and quality of the product  
    • They've had some weird failures on their brake actuators. One of them was because they added some kind of lubricant to the factory fill brake fluid that aftermarket brake fluid didn't have so it would affect the seals. Another was just mysterious, probably internal corrosion or something eating away at Prius brake actuators. Parts alone for those are a few thousand USD so not a cheap fix.
    • Selling a genuine Nissan Skyline R33 Coupe 8-Pin Power Window Master Switch Part No. 25401-26U10 Price $300   IMPUL Gear Knob – Rare JDM Upgrade Upgrade your interior with this genuine IMPUL gear knob – a rare and stylish addition to any JDM build. Premium quality, perfect fit, and an authentic Japanese touch for your ride.  Price:$300 Nissan Skyline R33 (Series 2) Sedan Tail Lights Immaculate Condition OEM JDM S2 a pair of OEM Skyline R33 Series 2 sedan tail lights in excellent condition. These are becoming harder to find, especially in this state. Price:$900   Located in Melbourne (Western Suburbs) – Shipping available Australia wide at buyer’s expense. DM if you need anymore details.  
    • KYBs are typically twin tube, putting them in the lower tier of desireability. Do you just want to replace worn out ones for the lowest cost? I mean, you wouldn't just replace one end of a car, if the rears are a similar age to the fronts, then they are probably nowhere near what they should be, and likely won't be great against brand new fronts. So, to spend ~$800 on 2nd tier dampers, when you could get a decent set of MCA coilovers for <$4k.....? As to the strut tops. 1st up, the Sparesbox site specifically tells you that they are not correct for an R33. Beyond that, why do you think you need them?
    • That's not very Toyota of the Toyota!
×
×
  • Create New...