Jump to content
SAU Community

Recommended Posts

I don't know either.

but my experience has been that as long as it is never registered, no-one tracks the car once it arrives.

but again, if you want something for parts surely a half cut is better, cheaper to buy and import and will probably have all the bits you need.

ok, i think its a 1995 rx7, you can only import them for race/rally use...

now, u can import one for about $13000 or cheaper

and in australia they are $30-50000

so if you have lets say a bare shell thats road legal in australia, would taking out the whole of the import and putting it into the aussie car make it legal?

yea i been dreaming about importing series 6-7 exracer rx7. i think you need a ANDRA licences but you could drive it on the road, (in wa) anyway with $12 permit's they only last 48hours so just pick one up every friday arvo and kill everyone on crusies on the weekends. also dont need to have number plates. prob wouldnt happen but its my dream.

so you can do that?

you can buy a race / rally use import, and swap everything into an australian road registered car and itll be legal?

thanks

No you cant do it as the motor is never to be in any other vehicle.

RX7's arent on the FIA list so you have to get a letter from CAMS to bring one in as of the last month.

They are cracking down big time.

nope, the car was under the old LEV scheme and the engine from a half cut...but of course the people who inspected for the blue slip didn't know where the engine came from.

My rally gtr on the other hand has been sitting around with a blown engine for about 6 months and is about to get a new one, but then that engine will be rebuilt and used elsewhere....I'm pretty sure there is no rule about how a part (eg engine) can be used once it has arrived in aus.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Has equal chance of cleaning an AFM and f**king an AFM. I think you can work out what happened. When the Hitachi ECU sees the AFM die and goes into the associated limp mode, then it will start and run just fine, because it ignores the AFM and just runs on idle maps that will do what it needs to get it going. But there is no proper load signal, so that's about all it can do. My suggestion? If you don't want to go full aftermaket ECU, then get some R35 GTR AFM cards and some housings to put them in, in the stock location, and Nistune the ECU. Better to do a good upgrade than just replace shitty 40 year old tech with the same 40 year old tech.
    • So my car was recently having trouble starting on initial crank, I would need to feather the gas for it to start up but besides that it would start and run fine. So I clicked the idle air control valve (with throttle body cleaner) and cleaned the MAF sensors (with MAF cleaner). The start up issue was fixed and now the car turns over without the assist of the throttle, but the car is in limp mode and wont rev past 2.5k RPM. From what I understand the IACV would not put the car in limp mode, so I am to believe it is the MAF sensors, but it was running fine before and now I cant get it out of limp mode. I cleaned the MAF made sure the o rings were seated properly. Made sure the cables were plugged in properly, the cables also both read the same voltage. Does anybody know why this is or what could be causing this or how to get it out of limp mode?
    • Ooo I might actually come and bring the kids, however will leave the shit box home and take the daily
    • Thanks. Yeah I realised that there's no way I'd be able to cover the holes with the filler, it would just fall through. Thanks again @GTSBoy!
    • That was the reason I asked. If you were going to be fully bodge spec, then that type of filler is the extreme bodge way to fill a large gap. But seeing as you're going to use glass sheet, I would only use that fibre reinforced filler if there are places that need a "bit more" after you've finished laying in the sheet. Which, ideally, you wouldn't. You might use a blob of it underneath the sheet, if you need to provide some support from under to keep the level of your sheet repair up as high as it needs to be, to minimise the amount of filler you need on top. Even though you're going bodge spec here, using glass instead of metal, the same rules apply wrt not having half inch deep filler on the top of the repair. Thick filler always ends up shitting the bed earlier than thin filler.
×
×
  • Create New...